http://pubwiki.slican.com/api.php?action=feedcontributions&feedformat=atom&user=GrzegorzzpubWiki-en - User contributions [en]2026-04-04T09:42:54ZUser contributionsMediaWiki 1.26.0http://pubwiki.slican.com/index.php?title=DPH.IP_Doorphone_connection&diff=7528DPH.IP Doorphone connection2017-10-13T08:26:42Z<p>Grzegorzz: </p>
<hr />
<div>Connecting doorphone can be executed via appropriate cables connected to connecting terminal located on doorphone PCB. Connecting terminal is visible and accessible afer unscrewing front panel, this operation is described in chapter [[DPH - Opening doorphone casing]].<br />
{{warning|Before connecting cables to connecting terminal, cables should be bring into the casing via hole located on casing backside.}}<br />
Connections located in connection terminal, usetd to doorphone installation are presented in following table:<br />
<center><br />
{|{{Prettytable}}<br />
|-<br />
|[[File:Ikona uziemiena biała.PNG]] || earthing (for proper operation of doorphone over-voltage protection)<br />
|-<br />
|LAN || RJ45 socket for LAN cable (PoE support)<br />
|-<br />
|EZ ||rowspan="2"| electrolock, 12V DC, max 0.7A <br />
|-<br />
|EZ<br />
|-<br />
|STA ||rowspan="2"| isolated normaly open relay connection used to control additional device - allowable voltage is equal to max 24V AC STA Max 0.7A<br />
|-<br />
|STA<br />
|-<br />
|AC ||rowspan="2"| power supply connections 24 - 48VDC<br />
|-<br />
|AC<br />
|-<br />
|COD || opening door sensor - disconnection from GND decrease EZ relay operation time<br />
|-<br />
|POD || opening door button (relative to GND)<br />
|-<br />
|GND || ground for POD, COD signals<br />
|}<br />
</center><br />
Connection scheme of doorphone DPH.IP-KSxx.C is presented on following figure.<br><br />
<center>[[File:DPH.IP-KSxxRF sch podlaczenia_eng.png]]</center><br><br />
<br />
Connection scheme of doorphone DPH.IP-CR0RF is presented on following figures.<br><br />
<center>[[File:DPH.IP-CR0RF_connection1.png|500px]] or [[File:DPH.IP-CR0RF_connection2.png|500px]]</center><br></div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=Characteristic_of_Slican_DPH.IP_doorphone&diff=7527Characteristic of Slican DPH.IP doorphone2017-10-11T11:30:43Z<p>Grzegorzz: </p>
<hr />
<div>Slican DPH.IP doorphone series connected to PBX enables to establish call between person near doorphone and PBX subscriber, as well as enter to protected area. It is also possible to trigger an electrolock, for opening door or gate, from phone connected to PBX.<br><br />
Additionally, DPH.IP doorphone can be used as fully functional access control system (ACS), due to registered events, that are send and visible in detailed billing application, or application designed especially for individual client. Thanks to installed, doorphone can control two relays (e.g. gate or doors), detect door opening or additional button pressing.<br><br />
Mounting additional '''CAM38.IP-KS''' camera module, allows to preview the surroundings and people that are using the doorphone with Slican's MessengerCTI.<br><br><br />
Slican offers three types or DPH.IP-KSxxRF.C devices:<br />
<br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>DEVICE MODEL</b></center> !!{{Hl1}}|<center><b>FEATURES</b></center><br />
|-<br />
| <center><b>DPH.IP-CR0RF</b></center> ||<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
** RFID card/pendant reader<br />
** one relay (EZ)<br />
** door opened sensor and button (COD, POD)<br />
* powered directly with PoE<br />
** RFID card/pendant reader<br />
<br />
|-<br />
| <center><b>DPH.IP-KS1RF.C</b></center> ||<br />
* doorphone with one call key<br />
* RFID card/pendant reader<br />
* support for CAM38.IP-KS camera module<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
<br />
|-<br />
| <center><b>DPH.IP-KS4DRF.C</b></center> ||<br />
* doorphone with four keys (two navigational, one answering and one dismissing a call)<br />
* LCD display for showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* support for CAM38.IP-KS camera module<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
<br />
|-<br />
| <center><b>DPH.IP-KS16DRF.C</b></center> ||<br />
* doorphone with full alphanumeric keyboard<br />
* LCD display for configuring the device and showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* support for CAM38.IP-KS camera module<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
|-<br />
| <center><b>[https://wiki.slican.pl/index.php/Doorphone_adapter_DPH.IP-UB2 DPH.IP-UB2.C]</b></center>||<br />
|}<br />
<br />
<br />
Following functions are available in DPH.IP doorphone (varies, depending on DPH model):<br />
* establish phone call using touch buttons arranged in form of numeric keyboard<br />
* two relays trigger:<br />
** electrolock (EZ)<br />
** additional relay (STA)<br />
* power supply with 12-25V AC lub 14-35V DC or PoE<br />
* environment temperature range -20 to +70 (below 0 degrees, display reating time increases up to 10 seconds)<br />
* inputs COD (opening door sensori) i POD (opening door button). Both buttons operate with electrolock.<br />
* EZ trigger (opening) by receiving '''„1”''' or '''„*”''' character in DTMF code<br />
* built-in RFID card reader (Unique 125kHz standard, in accordance with EM4102)<br />
* possibility to trigger EZ or STA by registered RFID card approach<br />
* STA trigger (second relay) by receiving '''"2"''' character in DTMF code. Single pulse with fixed duration time is generated<br />
<br />
=Maximum devices used depending on PBX type=<br />
<br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>PBX TYPE</b></center> !!{{Hl1}}|<center><b>DPH.IP</b></center><br />
|-<br />
| <center>IPL-256</center>||<center>99</center><br />
|-<br />
| <center>IPM-032</center> ||<center>99</center><br />
|-<br />
| <center>IPM-032.LowCost</center> ||<center>10</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>28</center><br />
|-<br />
| <center>IPU-14.102</center> ||<center>68</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.100,101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.104.105<br>(LowCost)</center> ||<center>8</center><br />
|-<br />
| <center>MAC-6400</center> ||<center>99</center><br />
|-<br />
| <center>CCT-1668</center> ||<center>60</center><br />
|}<br />
<br />
=Mounting=<br />
All DPH and DPH.IP-KSxxRFC series doorphones are manufactured in various designs and depending on the implementation, they can be installed<br />
* as over-plaster<br />
* as under-plaster<br />
* on the fence</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=Characteristic_of_Slican_DPH.IP_doorphone&diff=7526Characteristic of Slican DPH.IP doorphone2017-10-11T11:28:01Z<p>Grzegorzz: </p>
<hr />
<div>Slican DPH.IP doorphone series connected to PBX enables to establish call between person near doorphone and PBX subscriber, as well as enter to protected area. It is also possible to trigger an electrolock, for opening door or gate, from phone connected to PBX.<br><br />
Additionally, DPH.IP doorphone can be used as fully functional access control system (ACS), due to registered events, that are send and visible in detailed billing application, or application designed especially for individual client. Thanks to installed, doorphone can control two relays (e.g. gate or doors), detect door opening or additional button pressing.<br><br />
Mounting additional '''CAM38.IP-KS''' camera module, allows to preview the surroundings and people that are using the doorphone with Slican's MessengerCTI.<br><br><br />
Slican offers three types or DPH.IP-KSxxRF.C devices:<br />
<br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>DEVICE MODEL</b></center> !!{{Hl1}}|<center><b>FEATURES</b></center><br />
|-<br />
| <center><b>DPH.IP-CR0RF</b></center> ||<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
** RFID card/pendant reader<br />
** one relay (EZ)<br />
** door opened sensor and button (COD, POD)<br />
* powered directly with PoE<br />
** RFID card/pendant reader<br />
<br />
|-<br />
| <center><b>DPH.IP-KS1RF.C</b></center> ||<br />
* doorphone with one call key<br />
* RFID card/pendant reader<br />
* support for CAM38.IP-KS camera module<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
<br />
|-<br />
| <center><b>DPH.IP-KS4DRF.C</b></center> ||<br />
* doorphone with four keys (two navigational, one answering and one dismissing a call)<br />
* LCD display for showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* support for CAM38.IP-KS camera module<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
<br />
|-<br />
| <center><b>DPH.IP-KS16DRF.C</b></center> ||<br />
* doorphone with full alphanumeric keyboard<br />
* LCD display for configuring the device and showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* support for CAM38.IP-KS camera module<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
|-<br />
| <center><b>[https://wiki.slican.pl/index.php/Doorphone_adapter_DPH.IP-UB2 DPH.IP-KS16DRF.C]</b></center>||<br />
|}<br />
<br />
<br />
Following functions are available in DPH.IP doorphone (varies, depending on DPH model):<br />
* establish phone call using touch buttons arranged in form of numeric keyboard<br />
* two relays trigger:<br />
** electrolock (EZ)<br />
** additional relay (STA)<br />
* power supply with 12-25V AC lub 14-35V DC or PoE<br />
* environment temperature range -20 to +70 (below 0 degrees, display reating time increases up to 10 seconds)<br />
* inputs COD (opening door sensori) i POD (opening door button). Both buttons operate with electrolock.<br />
* EZ trigger (opening) by receiving '''„1”''' or '''„*”''' character in DTMF code<br />
* built-in RFID card reader (Unique 125kHz standard, in accordance with EM4102)<br />
* possibility to trigger EZ or STA by registered RFID card approach<br />
* STA trigger (second relay) by receiving '''"2"''' character in DTMF code. Single pulse with fixed duration time is generated<br />
* graphical LCD display (except DPH.IP-KS1RF.C)<br />
<br />
=Maximum devices used depending on PBX type=<br />
<br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>PBX TYPE</b></center> !!{{Hl1}}|<center><b>DPH.IP</b></center><br />
|-<br />
| <center>IPL-256</center>||<center>99</center><br />
|-<br />
| <center>IPM-032</center> ||<center>99</center><br />
|-<br />
| <center>IPM-032.LowCost</center> ||<center>10</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>28</center><br />
|-<br />
| <center>IPU-14.102</center> ||<center>68</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.100,101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.104.105<br>(LowCost)</center> ||<center>8</center><br />
|-<br />
| <center>MAC-6400</center> ||<center>99</center><br />
|-<br />
| <center>CCT-1668</center> ||<center>60</center><br />
|}<br />
<br />
=Mounting=<br />
All DPH and DPH.IP-KSxxRFC series doorphones are manufactured in various designs and depending on the implementation, they can be installed<br />
* as over-plaster<br />
* as under-plaster<br />
* on the fence</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_doorphone&diff=7525DPH.IP doorphone2017-10-11T11:16:26Z<p>Grzegorzz: /* Fence assembly */</p>
<hr />
<div><center>[[File:DPH.IP-CR0RF.png|250px]]</center> <br><br />
<center>[[File:DPH.IP-KS4RF.C.png|200px]] [[File:DPH.IP-KS16RF.C.png|200px]] [[File:DPH.IP-KS1RF.C.png|200px]]</center><br />
<br />
<center>'''Dorphone and RFID reader'''</center><br />
<br />
<center>'''DPH.IP'''</center><br />
<br />
<center>Product manual</center><br />
<br />
<center>Release 1.00</center><br />
<br />
<center>'''Slican Sp. z o.o.'''</center><br />
<br />
<center>[http://www.slican.pl/ www.slican.com] </center><br />
<br />
<center>e-mail: [mailto:office@slican.pl office@slican.pl]</center><br />
<br />
<center>Manufacturer reserves right to make changes without prior notification.</center><br />
<br />
<center>Date of last modification: 2017-06-06</center><br />
<br />
= [[Characteristic of Slican DPH.IP doorphone]] =<br />
<br />
== [[Characteristic and DPH.IP cassettes dimensions]] ==<br />
<br />
==[[DPH.IP Opening housing | Opening doorphone housing]]==<br />
<br />
== [[DPH16 - Doorphone assembly|Doorphone assembly]] ==<br />
==[[DPH.IP Doorphone keyboard]]==<br />
<br />
== [[DPH.IP Doorphone connection]] ==<br />
=== [[DPH.IP camera plug|Mounting camera module in DPH.IP doorphone]] ===<br />
<br />
== [[PBX configuration for doorphone operation]] ==<br />
<br />
== [[DPH.IP Doorphone programming]] ==<br />
<br />
== [[DPH16 - Doorphone using|Doorphone using]] ==<br />
<br />
= [[Safety requirements while using DPH series doorphones]] =<br />
<br />
= [[DPH.IP certificate of conformity and proper device disposal]] =</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_camera_plug&diff=7524DPH.IP camera plug2017-10-09T11:13:09Z<p>Grzegorzz: </p>
<hr />
<div>Each DPH.IP doorphone can be equipped with additional '''CAM38.IP-KS''' camera module , which allows to preview the surroundings and people that are using the doorphone.<br><br />
Camera module works with DPH.IP-KS.C and DPH.IP-UB2 doorphones.<br><br />
Part is sold separately, to mount it:<br />
* unplug the device from power supply<br />
* unscrew the housing and screws of the speaker holder<br />
install camera module in dedicated place, screw it to housing and connect to DPH.IP mainboard accordingly to picture below<br><br />
[[File: DPH.IP_camera module.png]]<br />
* screw the speaker holder and doorphone housing together<br />
<br><br />
Camera should register the picture after connecting it to PBX.<br><br />
To preview it, use Slican MessengerCTI application.<br />
<br><br><br />
Doorphones camera configuration is done with '''SPH.IP Camera Config''' application.<br><br />
[[File: DPH.IP.CAM.1.png]]<br><br />
After start, application will search all available in LAN camera built in DPH.IP doorphones. App window allows to configure IP interface of the device and to copy camera link, which should be assigned with doorphone in ConfigMAN or ConfigWEB application.<br><br />
[[File: DPH.IP.CAM.2.png]]<br><br />
Application is in polish version until releasing english language version.</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=File:DPH.IP.CAM.2.png&diff=7523File:DPH.IP.CAM.2.png2017-10-09T11:12:25Z<p>Grzegorzz: </p>
<hr />
<div></div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=File:DPH.IP.CAM.1.png&diff=7522File:DPH.IP.CAM.1.png2017-10-09T11:12:06Z<p>Grzegorzz: </p>
<hr />
<div></div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_camera_plug&diff=7521DPH.IP camera plug2017-10-09T10:40:14Z<p>Grzegorzz: </p>
<hr />
<div>Each DPH.IP doorphone can be equipped with additional '''CAM38.IP-KS''' camera module , which allows to preview the surroundings and people that are using the doorphone.<br><br />
Camera module works with DPH.IP-KS.C and DPH.IP-UB2 doorphones.<br><br />
Part is sold separately, to mount it:<br />
* unplug the device from power supply<br />
* unscrew the housing and screws of the speaker holder<br />
install camera module in dedicated place, screw it to housing and connect to DPH.IP mainboard accordingly to picture below<br><br />
[[File: DPH.IP_camera module.png]]<br />
* screw the speaker holder and doorphone housing together<br />
<br><br />
Camera should register the picture after connecting it to PBX.<br><br />
To preview it, use Slican MessengerCTI application.</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=Characteristic_of_Slican_DPH.IP_doorphone&diff=7520Characteristic of Slican DPH.IP doorphone2017-10-09T10:39:58Z<p>Grzegorzz: </p>
<hr />
<div>Slican DPH.IP doorphone series connected to PBX enables to establish call between person near doorphone and PBX subscriber, as well as enter to protected area. It is also possible to trigger an electrolock, for opening door or gate, from phone connected to PBX.<br><br />
Additionally, DPH.IP doorphone can be used as fully functional access control system (ACS), due to registered events, that are send and visible in detailed billing application, or application designed especially for individual client. Thanks to installed, doorphone can control two relays (e.g. gate or doors), detect door opening or additional button pressing.<br><br />
Mounting additional '''CAM38.IP-KS''' camera module, allows to preview the surroundings and people that are using the doorphone with Slican's MessengerCTI.<br><br><br />
Slican offers three types or DPH.IP-KSxxRF.C devices:<br />
<br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>DEVICE MODEL</b></center> !!{{Hl1}}|<center><b>FEATURES</b></center><br />
|-<br />
| <center><b>DPH.IP-CR0RF</b></center> ||<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
** RFID card/pendant reader<br />
** one relay (EZ)<br />
** door opened sensor and button (COD, POD)<br />
* powered directly with PoE<br />
** RFID card/pendant reader<br />
<br />
|-<br />
| <center><b>DPH.IP-KS1RF.C</b></center> ||<br />
* doorphone with one call key<br />
* RFID card/pendant reader<br />
* support for CAM38.IP-KS camera module<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
<br />
|-<br />
| <center><b>DPH.IP-KS4DRF.C</b></center> ||<br />
* doorphone with four keys (two navigational, one answering and one dismissing a call)<br />
* LCD display for showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* support for CAM38.IP-KS camera module<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
<br />
|-<br />
| <center><b>DPH.IP-KS16DRF.C</b></center> ||<br />
* doorphone with full alphanumeric keyboard<br />
* LCD display for configuring the device and showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* support for CAM38.IP-KS camera module<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
|}<br />
<br />
<br />
Following functions are available in DPH.IP doorphone (varies, depending on DPH model):<br />
* establish phone call using touch buttons arranged in form of numeric keyboard<br />
* two relays trigger:<br />
** electrolock (EZ)<br />
** additional relay (STA)<br />
* power supply with 12-25V AC lub 14-35V DC or PoE<br />
* environment temperature range -20 to +70 (below 0 degrees, display reating time increases up to 10 seconds)<br />
* inputs COD (opening door sensori) i POD (opening door button). Both buttons operate with electrolock.<br />
* EZ trigger (opening) by receiving '''„1”''' or '''„*”''' character in DTMF code<br />
* built-in RFID card reader (Unique 125kHz standard, in accordance with EM4102)<br />
* possibility to trigger EZ or STA by registered RFID card approach<br />
* STA trigger (second relay) by receiving '''"2"''' character in DTMF code. Single pulse with fixed duration time is generated<br />
* graphical LCD display (except DPH.IP-KS1RF.C)<br />
<br />
=Maximum devices used depending on PBX type=<br />
<br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>PBX TYPE</b></center> !!{{Hl1}}|<center><b>DPH.IP</b></center><br />
|-<br />
| <center>IPL-256</center>||<center>99</center><br />
|-<br />
| <center>IPM-032</center> ||<center>99</center><br />
|-<br />
| <center>IPM-032.LowCost</center> ||<center>10</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>28</center><br />
|-<br />
| <center>IPU-14.102</center> ||<center>68</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.100,101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.104.105<br>(LowCost)</center> ||<center>8</center><br />
|-<br />
| <center>MAC-6400</center> ||<center>99</center><br />
|-<br />
| <center>CCT-1668</center> ||<center>60</center><br />
|}<br />
<br />
=Mounting=<br />
All DPH and DPH.IP-KSxxRFC series doorphones are manufactured in various designs and depending on the implementation, they can be installed<br />
* as over-plaster<br />
* as under-plaster<br />
* on the fence</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=Characteristic_of_Slican_DPH.IP_doorphone&diff=7519Characteristic of Slican DPH.IP doorphone2017-10-09T07:26:22Z<p>Grzegorzz: </p>
<hr />
<div>Slican DPH.IP doorphone series connected to PBX enables to establish call between person near doorphone and PBX subscriber, as well as enter to protected area. It is also possible to trigger an electrolock, for opening door or gate, from phone connected to PBX.<br><br />
Additionally, DPH.IP doorphone can be used as fully functional access control system (ACS), due to registered events, that are send and visible in detailed billing application, or application designed especially for individual client. Thanks to installed, doorphone can control two relays (e.g. gate or doors), detect door opening or additional button pressing.<br><br />
Mounting additional '''CAM38.IP-KS''' camera module, allows to preview the surroundings and people that are using the doorphone with Slican's MessengerCTI application or any other that support video in rtsp:/......... format (e.g. VLC).<br><br><br />
Slican offers three types or DPH.IP-KSxxRF.C devices:<br />
<br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>DEVICE MODEL</b></center> !!{{Hl1}}|<center><b>FEATURES</b></center><br />
|-<br />
| <center><b>DPH.IP-CR0RF</b></center> ||<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
** RFID card/pendant reader<br />
** one relay (EZ)<br />
** door opened sensor and button (COD, POD)<br />
* powered directly with PoE<br />
** RFID card/pendant reader<br />
<br />
|-<br />
| <center><b>DPH.IP-KS1RF.C</b></center> ||<br />
* doorphone with one call key<br />
* RFID card/pendant reader<br />
* support for CAM38.IP-KS camera module<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
<br />
|-<br />
| <center><b>DPH.IP-KS4DRF.C</b></center> ||<br />
* doorphone with four keys (two navigational, one answering and one dismissing a call)<br />
* LCD display for showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* support for CAM38.IP-KS camera module<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
<br />
|-<br />
| <center><b>DPH.IP-KS16DRF.C</b></center> ||<br />
* doorphone with full alphanumeric keyboard<br />
* LCD display for configuring the device and showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* support for CAM38.IP-KS camera module<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
|}<br />
<br />
<br />
Following functions are available in DPH.IP doorphone (varies, depending on DPH model):<br />
* establish phone call using touch buttons arranged in form of numeric keyboard<br />
* two relays trigger:<br />
** electrolock (EZ)<br />
** additional relay (STA)<br />
* power supply with 12-25V AC lub 14-35V DC or PoE<br />
* environment temperature range -20 to +70 (below 0 degrees, display reating time increases up to 10 seconds)<br />
* inputs COD (opening door sensori) i POD (opening door button). Both buttons operate with electrolock.<br />
* EZ trigger (opening) by receiving '''„1”''' or '''„*”''' character in DTMF code<br />
* built-in RFID card reader (Unique 125kHz standard, in accordance with EM4102)<br />
* possibility to trigger EZ or STA by registered RFID card approach<br />
* STA trigger (second relay) by receiving '''"2"''' character in DTMF code. Single pulse with fixed duration time is generated<br />
* graphical LCD display (except DPH.IP-KS1RF.C)<br />
<br />
=Maximum devices used depending on PBX type=<br />
<br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>PBX TYPE</b></center> !!{{Hl1}}|<center><b>DPH.IP</b></center><br />
|-<br />
| <center>IPL-256</center>||<center>99</center><br />
|-<br />
| <center>IPM-032</center> ||<center>99</center><br />
|-<br />
| <center>IPM-032.LowCost</center> ||<center>10</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>28</center><br />
|-<br />
| <center>IPU-14.102</center> ||<center>68</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.100,101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.104.105<br>(LowCost)</center> ||<center>8</center><br />
|-<br />
| <center>MAC-6400</center> ||<center>99</center><br />
|-<br />
| <center>CCT-1668</center> ||<center>60</center><br />
|}<br />
<br />
=Mounting=<br />
All DPH and DPH.IP-KSxxRFC series doorphones are manufactured in various designs and depending on the implementation, they can be installed<br />
* as over-plaster<br />
* as under-plaster<br />
* on the fence</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=Characteristic_of_Slican_DPH.IP_doorphone&diff=7518Characteristic of Slican DPH.IP doorphone2017-10-09T07:25:55Z<p>Grzegorzz: </p>
<hr />
<div>Slican DPH.IP doorphone series connected to PBX enables to establish call between person near doorphone and PBX subscriber, as well as enter to protected area. It is also possible to trigger an electrolock, for opening door or gate, from phone connected to PBX.<br><br />
Additionally, DPH.IP doorphone can be used as fully functional access control system (ACS), due to registered events, that are send and visible in detailed billing application, or application designed especially for individual client. Thanks to installed, doorphone can control two relays (e.g. gate or doors), detect door opening or additional button pressing.<br><br />
Mounting additional '''CAM38.IP-KS''' camera module, allows to preview the surroundings and people that are using the doorphone with Slican's MessengerCTI application or any other that support video in rtsp:/......... format (e.g. VLC). .<br />
Slican offers three types or DPH.IP-KSxxRF.C devices:<br />
<br><br><br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>DEVICE MODEL</b></center> !!{{Hl1}}|<center><b>FEATURES</b></center><br />
|-<br />
| <center><b>DPH.IP-CR0RF</b></center> ||<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
** RFID card/pendant reader<br />
** one relay (EZ)<br />
** door opened sensor and button (COD, POD)<br />
* powered directly with PoE<br />
** RFID card/pendant reader<br />
<br />
|-<br />
| <center><b>DPH.IP-KS1RF.C</b></center> ||<br />
* doorphone with one call key<br />
* RFID card/pendant reader<br />
* support for CAM38.IP-KS camera module<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
<br />
|-<br />
| <center><b>DPH.IP-KS4DRF.C</b></center> ||<br />
* doorphone with four keys (two navigational, one answering and one dismissing a call)<br />
* LCD display for showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* support for CAM38.IP-KS camera module<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
<br />
|-<br />
| <center><b>DPH.IP-KS16DRF.C</b></center> ||<br />
* doorphone with full alphanumeric keyboard<br />
* LCD display for configuring the device and showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* support for CAM38.IP-KS camera module<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
|}<br />
<br />
<br />
Following functions are available in DPH.IP doorphone (varies, depending on DPH model):<br />
* establish phone call using touch buttons arranged in form of numeric keyboard<br />
* two relays trigger:<br />
** electrolock (EZ)<br />
** additional relay (STA)<br />
* power supply with 12-25V AC lub 14-35V DC or PoE<br />
* environment temperature range -20 to +70 (below 0 degrees, display reating time increases up to 10 seconds)<br />
* inputs COD (opening door sensori) i POD (opening door button). Both buttons operate with electrolock.<br />
* EZ trigger (opening) by receiving '''„1”''' or '''„*”''' character in DTMF code<br />
* built-in RFID card reader (Unique 125kHz standard, in accordance with EM4102)<br />
* possibility to trigger EZ or STA by registered RFID card approach<br />
* STA trigger (second relay) by receiving '''"2"''' character in DTMF code. Single pulse with fixed duration time is generated<br />
* graphical LCD display (except DPH.IP-KS1RF.C)<br />
<br />
=Maximum devices used depending on PBX type=<br />
<br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>PBX TYPE</b></center> !!{{Hl1}}|<center><b>DPH.IP</b></center><br />
|-<br />
| <center>IPL-256</center>||<center>99</center><br />
|-<br />
| <center>IPM-032</center> ||<center>99</center><br />
|-<br />
| <center>IPM-032.LowCost</center> ||<center>10</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>28</center><br />
|-<br />
| <center>IPU-14.102</center> ||<center>68</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.100,101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.104.105<br>(LowCost)</center> ||<center>8</center><br />
|-<br />
| <center>MAC-6400</center> ||<center>99</center><br />
|-<br />
| <center>CCT-1668</center> ||<center>60</center><br />
|}<br />
<br />
=Mounting=<br />
All DPH and DPH.IP-KSxxRFC series doorphones are manufactured in various designs and depending on the implementation, they can be installed<br />
* as over-plaster<br />
* as under-plaster<br />
* on the fence</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_camera_plug&diff=7517DPH.IP camera plug2017-10-06T13:25:58Z<p>Grzegorzz: Created page with "Each DPH.IP doorphone can be equipped with additional '''CAM38.IP-KS''' camera module , which allows to preview the surroundings and people that are using the doorphone.<br> C..."</p>
<hr />
<div>Each DPH.IP doorphone can be equipped with additional '''CAM38.IP-KS''' camera module , which allows to preview the surroundings and people that are using the doorphone.<br><br />
Camera module works with DPH.IP-KS.C and DPH.IP-UB2 doorphones.<br><br />
Part is sold separately, to mount it:<br />
* unplug the device from power supply<br />
* unscrew the housing and screws of the speaker holder<br />
install camera module in dedicated place, screw it to housing and connect to DPH.IP mainboard accordingly to picture below<br><br />
[[File: DPH.IP_camera module.png]]<br />
* screw the speaker holder and doorphone housing together<br />
<br><br />
Camera should register the picture after connecting it to PBX.<br><br />
To preview it, use Slican MessengerCTI application or any other that support video in '''rtsp:/.........''' format (e.g. VLC).</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=File:DPH.IP_camera_module.png&diff=7516File:DPH.IP camera module.png2017-10-06T13:25:49Z<p>Grzegorzz: </p>
<hr />
<div></div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_doorphone&diff=7515DPH.IP doorphone2017-10-06T13:17:30Z<p>Grzegorzz: /* = Mounting camera module in DPH.IP doorphone */</p>
<hr />
<div><center>[[File:DPH.IP-CR0RF.png|250px]]</center> <br><br />
<center>[[File:DPH.IP-KS4RF.C.png|200px]] [[File:DPH.IP-KS16RF.C.png|200px]] [[File:DPH.IP-KS1RF.C.png|200px]]</center><br />
<br />
<center>'''Dorphone and RFID reader'''</center><br />
<br />
<center>'''DPH.IP'''</center><br />
<br />
<center>Product manual</center><br />
<br />
<center>Release 1.00</center><br />
<br />
<center>'''Slican Sp. z o.o.'''</center><br />
<br />
<center>[http://www.slican.pl/ www.slican.com] </center><br />
<br />
<center>e-mail: [mailto:office@slican.pl office@slican.pl]</center><br />
<br />
<center>Manufacturer reserves right to make changes without prior notification.</center><br />
<br />
<center>Date of last modification: 2017-06-06</center><br />
<br />
= [[Characteristic of Slican DPH.IP doorphone]] =<br />
<br />
== [[Characteristic and DPH.IP cassettes dimensions]] ==<br />
<br />
==[[DPH.IP Opening housing | Opening doorphone housing]]==<br />
<br />
== [[DPH16 - Doorphone assembly|Doorphone assembly]] ==<br />
===[[DPH16 - Assembly on fence|Fence assembly]]===<br />
<br />
==[[DPH.IP Doorphone keyboard]]==<br />
<br />
== [[DPH.IP Doorphone connection]] ==<br />
=== [[DPH.IP camera plug|Mounting camera module in DPH.IP doorphone]] ===<br />
<br />
== [[PBX configuration for doorphone operation]] ==<br />
<br />
== [[DPH.IP Doorphone programming]] ==<br />
<br />
== [[DPH16 - Doorphone using|Doorphone using]] ==<br />
<br />
= [[Safety requirements while using DPH series doorphones]] =<br />
<br />
= [[DPH.IP certificate of conformity and proper device disposal]] =</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_doorphone&diff=7514DPH.IP doorphone2017-10-06T13:17:04Z<p>Grzegorzz: /* DPH.IP Doorphone connection */</p>
<hr />
<div><center>[[File:DPH.IP-CR0RF.png|250px]]</center> <br><br />
<center>[[File:DPH.IP-KS4RF.C.png|200px]] [[File:DPH.IP-KS16RF.C.png|200px]] [[File:DPH.IP-KS1RF.C.png|200px]]</center><br />
<br />
<center>'''Dorphone and RFID reader'''</center><br />
<br />
<center>'''DPH.IP'''</center><br />
<br />
<center>Product manual</center><br />
<br />
<center>Release 1.00</center><br />
<br />
<center>'''Slican Sp. z o.o.'''</center><br />
<br />
<center>[http://www.slican.pl/ www.slican.com] </center><br />
<br />
<center>e-mail: [mailto:office@slican.pl office@slican.pl]</center><br />
<br />
<center>Manufacturer reserves right to make changes without prior notification.</center><br />
<br />
<center>Date of last modification: 2017-06-06</center><br />
<br />
= [[Characteristic of Slican DPH.IP doorphone]] =<br />
<br />
== [[Characteristic and DPH.IP cassettes dimensions]] ==<br />
<br />
==[[DPH.IP Opening housing | Opening doorphone housing]]==<br />
<br />
== [[DPH16 - Doorphone assembly|Doorphone assembly]] ==<br />
===[[DPH16 - Assembly on fence|Fence assembly]]===<br />
<br />
==[[DPH.IP Doorphone keyboard]]==<br />
<br />
== [[DPH.IP Doorphone connection]] ==<br />
==== [[DPH.IP camera plug|Mounting camera module in DPH.IP doorphone]] ===<br />
<br />
== [[PBX configuration for doorphone operation]] ==<br />
<br />
== [[DPH.IP Doorphone programming]] ==<br />
<br />
== [[DPH16 - Doorphone using|Doorphone using]] ==<br />
<br />
= [[Safety requirements while using DPH series doorphones]] =<br />
<br />
= [[DPH.IP certificate of conformity and proper device disposal]] =</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=Main_Page&diff=7513Main Page2017-09-08T07:15:41Z<p>Grzegorzz: /* News */</p>
<hr />
<div>{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=<br />
|title=Slican '''PUB'''lic '''WIKI''' in '''EN'''glish<br />
|text= '''KNOWLEDGE BASE OF SLICAN PRODUCTS USRES - ENJOY READING'''<br />
}}<br />
<br />
=News=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:news_4.png<br />
|title=Important news<br />
|text=<br />
* [http://pubwiki.slican.com/index.php/DPH.IP_doorphone New doorphones and card readers - DPH.IP series]<br />
* New PBX - NCP-PBX<br />
* [[Firmware:_Wersja_6.30_en | Version 6.30 of software for Slican servers]]<br />
* [[VoIP_account_in_CM_6.30_en | The change in the configuration of VoIP accounts in software version 6.30!]]<br />
* [[Slican_IPS_en|New type of IP servers - IPS-08]]<br />
* [[Adapter_CTS-DHSG_Instrukcja_obsługi_en| Slican CTS-DHSG adapter compatibility]]<br />
}}<br />
<br />
=NCP-PBX=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:CM400_swicth_GW.png<br />
|title=NCP-PBX<br />
|text=<br />
<br />
* [[NCP technical data| NCP-PBX Informations]]<br />
* [[NCP technical specification|Technical Specification]]<br />
}}<br />
<br />
=ITS=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:ITS Rzut small.jpg<br />
|title=IP-PBX - Slican ITS<br />
|text=<br />
<br />
* [[Slican ITS | ITS - information]]<br />
* [[ITS Instruction manual]]<br />
* [[ITS - PBX firmware]]<br />
* [[Slican ITS#Models| ITS Models ]]<br />
* [[Slican_ITS_View#Terminals_View| ITS Terminals]]<br />
}}<br />
<br />
=IPS-08=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:ITS Rzut small.jpg<br />
|title=IPS-08 Telecommunication server<br />
|text=<br />
<br />
* [[Dane_techniczne_centrali_IPS-08/IPS Technical information| IPS-08 information]]<br />
* [[IPS manual | Instruction Manual]]<br />
* [[Software | Supported applications]]<br />
* [[IPS_firmware | IPS-08 firmware]]<br />
<br />
}}<br />
=IPU-14=<br />
{{Bialy|IPU-14}}<br />
{{titled_frame<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:IPU_front_small.png<br />
|title=IPU-14 Telecommunication server<br />
|text=<br />
<br />
* [[IPU_technical_information/IPU_technical_information| IPU-14 information]]<br />
* [[IPU manual | Instruction manual]]<br />
* [[Software | Supported applications]]<br />
}}<br />
<br />
=IPM-032=<br />
{{Bialy|IPM-032}}<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:IPM-032 obie.jpg<br />
|title=IPM-032 Telecommunication server<br />
|text=<br />
* [[IPM Technical information| IPM-032 information]]<br />
* [[IPM instruction manual | Instruction Manual]]<br />
* [[Software | Supported applications]]<br />
}}<br />
<br />
=IPL-0256=<br />
{{Bialy|IPL-0256}}<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:IPL_both.jpg<br />
|title=IPL-256 Telecommunication server<br />
|text=<br />
<br />
* [[IPL Technical_information | IPL-256 information]]<br />
* [[IPL manual | Instruction Manual]]<br />
* [[Software | Supported applications]]<br />
}}<br />
<br />
=MAC-6400=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:MAC6400_M.jpg<br />
|title=MAC-6400/MAC-ZERO Telecommunication server<br />
|text=<br />
<br />
* [[MAC-6400 Information |MAC-6400 - Information]]<br />
* [[Instruction manual MAC|Instruction manual MAC-6400]]<br />
* [[Software | Supported applications]]<br />
* [[PBX firmware|MAC-6400 - PBX firmware]]<br />
}}<br />
<br />
=System phones=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:Telefony_202-102-330.png<br />
|title=System phones<br />
|text=<br />
<br />
* [[CTS-102 - information|CTS-102.CL CTS-102.HT CTS-102.IP - Instruction manual]]<br />
* [[CTS-202 - information|CTS-202.CL CTS-202.BT CTS-202.IP CTS-203.IP-PoE - Instruction manual]]<br />
* [[CTS-220 information|CTS-220 - Instruction manual]]<br />
* [[CTS-330 information|CTS-330/CTS-330.IP - Information]]<br />
* [[XL-2023ID - information|XL-2023ID - Instruction manual]]<br />
* [[VPS - VoIP phones]]<br />
}}<br />
<br />
=Doorphone and doorphone PBX systems=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=Image:Bramofony.jpg<br />
|title=BRV, HAS, SKD, DPH<br />
|text=<br />
<br />
* [[BRV - Instruction manual]]<br />
* [[HLP-22 - Instruction manual]]<br />
* [[DPH 1- and 2-button doorphone_v1_02|DPH 1- and 2-button doorphone]]<br />
* [[DPH 16-button doorphone_v1_02|DPH 16-button doorphone]]<br />
* [[DPH.IP doorphone]]<br />
* [[HAS-3000 - Instruction manual]]<br />
* [[HAS-3032 - Instruction manual]] <br />
* [[SKD_Instruction manual_v1.03|SKD - Instruction manual]]<br />
}}<br />
<br />
={{Bialy|Other products}}=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=Image:MAB_1101_S.jpg<br />
|title=Other products<br />
|text=<br />
<br />
* [[MAB-1101 information]]<br />
* [[MAB-1101 Instruction manual]]<br />
* [[MSB-1102 Instruction manual]]<br />
}}<br />
<br />
=DECT system=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:DECT.PNG<br />
|title=System DECT<br />
|text=<br />
<br />
* [[Opinion concerning Slican DECT-IP system]]<br />
* [[FAQ - DECT]]<br />
}}<br />
<br />
=Software=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:Billingman.jpg<br />
|title=Computer software<br />
|text=<br />
* [[WebCTI|WebCTI Instruction manual]]<br />
* [[PhoneCTI|PhoneCTI Instruction manual]]<br />
<!-- * [[PhoneCTI_voip|PhoneCTI.voip Instruction manual]] --><br />
* [[RecordMAN.client|RecordMAN.client Instruction manual]] - application to maintain recordings (downloading, playing, searching) stored using embedded recording systems working in CCT-1668, CXS-0424, MAC-6400, IPL-0256, IPM-032, IPU-14.<br />
* [[SenderSMS_manual|SenderSMS Instruction manual]] - application for sending/receiving group SMS messages<br />
* [[RecordMAN.server|RecordMAN.server Instruction manual]] - application to automatic downloading recording from PBX.<br />
* [[TouchCTI Instruction manual|TouchCTI]] - application to computer maintaining incoming calls using touch screen<br />
* [[BillingMAN_Instruction_manual |BillingMAN]] - application for call charges maintaining<br />
* [[TAPI]] - driver for cooperating Slican servers with external applications ex. MS Outlook<br />
}}<br />
<br />
=VoIP=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:VoIP_Slican_Wiki.png<br />
|title=VoIP in Slican<br />
|text=<br />
* [[VoIP call quality | VoIP call quality]]<br />
* [[Skype_in_Slican_server |How to configure Skype for cooperation with Slican server?]]<br />
}}<br />
<br />
=Withdrawn products=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:CXS 300px.jpg<br />
|title=Withdrawn products<br />
|text=<br />
[[Product withdrawn from production]]<br />
}}</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_doorphone&diff=7512DPH.IP doorphone2017-09-08T07:12:22Z<p>Grzegorzz: </p>
<hr />
<div><center>[[File:DPH.IP-CR0RF.png|250px]]</center> <br><br />
<center>[[File:DPH.IP-KS4RF.C.png|200px]] [[File:DPH.IP-KS16RF.C.png|200px]] [[File:DPH.IP-KS1RF.C.png|200px]]</center><br />
<br />
<center>'''Dorphone and RFID reader'''</center><br />
<br />
<center>'''DPH.IP'''</center><br />
<br />
<center>Product manual</center><br />
<br />
<center>Release 1.00</center><br />
<br />
<center>'''Slican Sp. z o.o.'''</center><br />
<br />
<center>[http://www.slican.pl/ www.slican.com] </center><br />
<br />
<center>e-mail: [mailto:office@slican.pl office@slican.pl]</center><br />
<br />
<center>Manufacturer reserves right to make changes without prior notification.</center><br />
<br />
<center>Date of last modification: 2017-06-06</center><br />
<br />
= [[Characteristic of Slican DPH.IP doorphone]] =<br />
<br />
== [[Characteristic and DPH.IP cassettes dimensions]] ==<br />
<br />
==[[DPH.IP Opening housing | Opening doorphone housing]]==<br />
<br />
== [[DPH16 - Doorphone assembly|Doorphone assembly]] ==<br />
===[[DPH16 - Assembly on fence|Fence assembly]]===<br />
<br />
==[[DPH.IP Doorphone keyboard]]==<br />
<br />
== [[DPH.IP Doorphone connection]] ==<br />
<br />
== [[PBX configuration for doorphone operation]] ==<br />
<br />
== [[DPH.IP Doorphone programming]] ==<br />
<br />
== [[DPH16 - Doorphone using|Doorphone using]] ==<br />
<br />
= [[Safety requirements while using DPH series doorphones]] =<br />
<br />
= [[DPH.IP certificate of conformity and proper device disposal]] =</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=File:DPH.IP-CR0RF.png&diff=7511File:DPH.IP-CR0RF.png2017-09-08T07:12:07Z<p>Grzegorzz: </p>
<hr />
<div></div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=Main_Page&diff=7510Main Page2017-09-08T06:57:38Z<p>Grzegorzz: /* Doorphone and doorphone PBX systems */</p>
<hr />
<div>{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=<br />
|title=Slican '''PUB'''lic '''WIKI''' in '''EN'''glish<br />
|text= '''KNOWLEDGE BASE OF SLICAN PRODUCTS USRES - ENJOY READING'''<br />
}}<br />
<br />
=News=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:news_4.png<br />
|title=Important news<br />
|text=<br />
* New PBX - NCP-PBX<br />
<!--* [[Firmware:_Wersja_6.40_en | New version 6.40 of software for Slican servers]]--><br />
* [[Firmware:_Wersja_6.30_en | Version 6.30 of software for Slican servers]]<br />
* [[VoIP_account_in_CM_6.30_en | The change in the configuration of VoIP accounts in software version 6.30!]]<br />
* [[Slican_IPS_en|New type of IP servers - IPS-08]]<br />
* [[Adapter_CTS-DHSG_Instrukcja_obsługi_en| Slican CTS-DHSG adapter compatibility]]<br />
<!--* [[Version 4.11 |News in version 4.11 of firmware for Slican servers]]--><br />
<br />
}}<br />
<br />
=NCP-PBX=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:CM400_swicth_GW.png<br />
|title=NCP-PBX<br />
|text=<br />
<br />
* [[NCP technical data| NCP-PBX Informations]]<br />
* [[NCP technical specification|Technical Specification]]<br />
}}<br />
<br />
=ITS=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:ITS Rzut small.jpg<br />
|title=IP-PBX - Slican ITS<br />
|text=<br />
<br />
* [[Slican ITS | ITS - information]]<br />
* [[ITS Instruction manual]]<br />
* [[ITS - PBX firmware]]<br />
* [[Slican ITS#Models| ITS Models ]]<br />
* [[Slican_ITS_View#Terminals_View| ITS Terminals]]<br />
}}<br />
<br />
=IPS-08=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:ITS Rzut small.jpg<br />
|title=IPS-08 Telecommunication server<br />
|text=<br />
<br />
* [[Dane_techniczne_centrali_IPS-08/IPS Technical information| IPS-08 information]]<br />
* [[IPS manual | Instruction Manual]]<br />
* [[Software | Supported applications]]<br />
* [[IPS_firmware | IPS-08 firmware]]<br />
<br />
}}<br />
=IPU-14=<br />
{{Bialy|IPU-14}}<br />
{{titled_frame<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:IPU_front_small.png<br />
|title=IPU-14 Telecommunication server<br />
|text=<br />
<br />
* [[IPU_technical_information/IPU_technical_information| IPU-14 information]]<br />
* [[IPU manual | Instruction manual]]<br />
* [[Software | Supported applications]]<br />
}}<br />
<br />
=IPM-032=<br />
{{Bialy|IPM-032}}<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:IPM-032 obie.jpg<br />
|title=IPM-032 Telecommunication server<br />
|text=<br />
* [[IPM Technical information| IPM-032 information]]<br />
* [[IPM instruction manual | Instruction Manual]]<br />
* [[Software | Supported applications]]<br />
}}<br />
<br />
=IPL-0256=<br />
{{Bialy|IPL-0256}}<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:IPL_both.jpg<br />
|title=IPL-256 Telecommunication server<br />
|text=<br />
<br />
* [[IPL Technical_information | IPL-256 information]]<br />
* [[IPL manual | Instruction Manual]]<br />
* [[Software | Supported applications]]<br />
}}<br />
<br />
=MAC-6400=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:MAC6400_M.jpg<br />
|title=MAC-6400/MAC-ZERO Telecommunication server<br />
|text=<br />
<br />
* [[MAC-6400 Information |MAC-6400 - Information]]<br />
* [[Instruction manual MAC|Instruction manual MAC-6400]]<br />
* [[Software | Supported applications]]<br />
* [[PBX firmware|MAC-6400 - PBX firmware]]<br />
}}<br />
<br />
=System phones=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:Telefony_202-102-330.png<br />
|title=System phones<br />
|text=<br />
<br />
* [[CTS-102 - information|CTS-102.CL CTS-102.HT CTS-102.IP - Instruction manual]]<br />
* [[CTS-202 - information|CTS-202.CL CTS-202.BT CTS-202.IP CTS-203.IP-PoE - Instruction manual]]<br />
* [[CTS-220 information|CTS-220 - Instruction manual]]<br />
* [[CTS-330 information|CTS-330/CTS-330.IP - Information]]<br />
* [[XL-2023ID - information|XL-2023ID - Instruction manual]]<br />
* [[VPS - VoIP phones]]<br />
}}<br />
<br />
=Doorphone and doorphone PBX systems=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=Image:Bramofony.jpg<br />
|title=BRV, HAS, SKD, DPH<br />
|text=<br />
<br />
* [[BRV - Instruction manual]]<br />
* [[HLP-22 - Instruction manual]]<br />
* [[DPH 1- and 2-button doorphone_v1_02|DPH 1- and 2-button doorphone]]<br />
* [[DPH 16-button doorphone_v1_02|DPH 16-button doorphone]]<br />
* [[DPH.IP doorphone]]<br />
* [[HAS-3000 - Instruction manual]]<br />
* [[HAS-3032 - Instruction manual]] <br />
* [[SKD_Instruction manual_v1.03|SKD - Instruction manual]]<br />
}}<br />
<br />
={{Bialy|Other products}}=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=Image:MAB_1101_S.jpg<br />
|title=Other products<br />
|text=<br />
<br />
* [[MAB-1101 information]]<br />
* [[MAB-1101 Instruction manual]]<br />
* [[MSB-1102 Instruction manual]]<br />
}}<br />
<br />
=DECT system=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:DECT.PNG<br />
|title=System DECT<br />
|text=<br />
<br />
* [[Opinion concerning Slican DECT-IP system]]<br />
* [[FAQ - DECT]]<br />
}}<br />
<br />
=Software=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:Billingman.jpg<br />
|title=Computer software<br />
|text=<br />
* [[WebCTI|WebCTI Instruction manual]]<br />
* [[PhoneCTI|PhoneCTI Instruction manual]]<br />
<!-- * [[PhoneCTI_voip|PhoneCTI.voip Instruction manual]] --><br />
* [[RecordMAN.client|RecordMAN.client Instruction manual]] - application to maintain recordings (downloading, playing, searching) stored using embedded recording systems working in CCT-1668, CXS-0424, MAC-6400, IPL-0256, IPM-032, IPU-14.<br />
* [[SenderSMS_manual|SenderSMS Instruction manual]] - application for sending/receiving group SMS messages<br />
* [[RecordMAN.server|RecordMAN.server Instruction manual]] - application to automatic downloading recording from PBX.<br />
* [[TouchCTI Instruction manual|TouchCTI]] - application to computer maintaining incoming calls using touch screen<br />
* [[BillingMAN_Instruction_manual |BillingMAN]] - application for call charges maintaining<br />
* [[TAPI]] - driver for cooperating Slican servers with external applications ex. MS Outlook<br />
}}<br />
<br />
=VoIP=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:VoIP_Slican_Wiki.png<br />
|title=VoIP in Slican<br />
|text=<br />
* [[VoIP call quality | VoIP call quality]]<br />
* [[Skype_in_Slican_server |How to configure Skype for cooperation with Slican server?]]<br />
}}<br />
<br />
=Withdrawn products=<br />
{{titled_frame|<br />
|title-font-size=200%<br />
|title-align=center<br />
|image=File:CXS 300px.jpg<br />
|title=Withdrawn products<br />
|text=<br />
[[Product withdrawn from production]]<br />
}}</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_Doorphone_programming&diff=7509DPH.IP Doorphone programming2017-07-07T12:51:34Z<p>Grzegorzz: /* DPH.IP-CR0RF and DPH.IP-KSxRF.C */</p>
<hr />
<div>Basic DPH.IP-KS16DRF.C doorphone configuration (IP address, VoIP server) can be made by built-in Menu, with display and keyboard. Detailed configuration of the device is made only with a application for PBX configuration, to which we connect the doorphone.<br><br />
Entering the Menu is made by double pressing the [[File:DPH16-Kluczyk.PNG|30px]] key on doorphone’s keyboard on not configured device (not connected to any PBX).<br />
<br />
=PIN code=<br />
DPH.IP-KS16DRF.C doorphone can be assigned with a PIN code, that allows to enter doorphone's Menu. PIN code in not set by deafult. It can be set in PBX configuration application.<br />
{{warning|Turning the doorphone on with short circiuted SETUP jumpers will change the settings to default (factory reset), and deleting the PIN code.}}<br />
<br />
=Doorphone IP configuration=<br />
DPH.IP doorphone configuration is basically simple and it comes down to connecting doorphone to network, adding it and configuring in PBX management application.<br><br />
When doorphone will be used in not standard network environment or e.g will be used in routed network (from Internet), additional configuration will be required. For DPH.IP Doorphone to work correctly in such conditions, it is necessary to:<br />
<br />
==Manually configure doorphone's IP address==<br />
By entering the Menu with double click the [[File:DPH16-Kluczyk.PNG|30px]] key, and choosing <b>VoIP</b> and <b>IP Configuration</b>, using arrows ↓ and ↑, we select, if doorphone should use IP address form DHCP server, or manually configured. Highlighting the options (IP address, Netmask, Gateway) and clicking OK will display used parameters. If we are using manual settings, it will be possible to change those values with keyboard. Trying to change those values, while DHCP client is turned on, will result in dislplaying proper notice.<br />
<br />
==Manually configure VoIP server address==<br />
VoIP server is configured in Menu, after selecting <b>VoIP</b> and next <b>VoIP server</b>. Doorphone can automatically connect to a PBX, which has such equipment already configured, or by manually enterind Domain or IP address.<br><br />
Device authorization is made based on MAC address.<br />
{{warning|MAC address configured in multiple PBXes will result in situation, that when DPH will automatically search for VoIP server, it will connect to a random PBX.}}<br />
If we choose NO, while asked about automatical VoIP server search, with keyboard, we can enter Domain or IP address of VoIP server. Changing the method of input, from letters and digits to digits alone, is made with [[File:DPH16-Kluczyk.PNG|30px]] key during typing the address.<br />
{{warning|After setting the doorphone from Menu, further configuration is possible only from application for PBX configuration.<br>Check changes made in PBX application that regard DPH.IP configuration. Improper parameters can result in disconnecting doorphone from PBX. Manual changes (locally from DPH.IP mennu) will be needed.}}<br />
Changing DPH.IP configuration from PBX application, while it is disconnected, will result, that, after restoring connection, doorphone configuration will overwrite configuration made in PBX application.<br />
<br />
=DPH.IP-CRORF and DPH.IP-KSxRF.C=<br />
When turning on a doorphone without alphanumeric keyboard, DHCP client and automatic VoIP server searching features are on. After connecting the doorphone to the same network as PBX, it will be possible to configure the device from PBX configuration application and therefore changing its IP address.<br><br />
Doorphone authorization is based on MAC address matching, so it will be necessary to accept a device in PBX.<br><br />
This series doorphones do not allow for configuration directly in the device.</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_Doorphone_connection&diff=7508DPH.IP Doorphone connection2017-07-07T12:50:15Z<p>Grzegorzz: </p>
<hr />
<div>Connecting doorphone can be executed via appropriate cables connected to connecting terminal located on doorphone PCB. Connecting terminal is visible and accessible afer unscrewing front panel, this operation is described in chapter [[DPH - Opening doorphone casing]].<br />
{{warning|Before connecting cables to connecting terminal, cables should be bring into the casing via hole located on casing backside.}}<br />
Connections located in connection terminal, usetd to doorphone installation are presented in following table:<br />
<center><br />
{|{{Prettytable}}<br />
|-<br />
|[[File:Ikona uziemiena biała.PNG]] || earthing (for proper operation of doorphone over-voltage protection)<br />
|-<br />
|LAN || RJ45 socket for LAN cable (PoE support)<br />
|-<br />
|EZ ||rowspan="2"| electrolock, 12V DC, max 0.7A <br />
|-<br />
|EZ<br />
|-<br />
|STA ||rowspan="2"| isolated normaly open relay connection used to control additional device - allowable voltage is equal to max 24V AC STA Max 0.7A<br />
|-<br />
|STA<br />
|-<br />
|AC ||rowspan="2"| power supply connections 14 - 35VDC or 12 - 25VAC<br />
|-<br />
|AC<br />
|-<br />
|COD || opening door sensor - disconnection from GND decrease EZ relay operation time<br />
|-<br />
|POD || opening door button (relative to GND)<br />
|-<br />
|GND || ground for POD, COD signals<br />
|}<br />
</center><br />
Connection scheme of doorphone DPH.IP-KSxx.C is presented on following figure.<br><br />
<center>[[File:DPH.IP-KSxxRF sch podlaczenia_eng.png]]</center><br><br />
<br />
Connection scheme of doorphone DPH.IP-CR0RF is presented on following figures.<br><br />
<center>[[File:DPH.IP-CR0RF_connection1.png|500px]] or [[File:DPH.IP-CR0RF_connection2.png|500px]]</center><br></div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH16_-_Doorphone_assembly&diff=7507DPH16 - Doorphone assembly2017-07-07T12:42:30Z<p>Grzegorzz: </p>
<hr />
<div>As mentioned above, DPH doorphone is suitable for under- and over-plaster assembly. On following figure, you can see the backside of DPH doorphone casing.<br />
<center>[[File:DPH tyl oznaczenia.png|200px]]</center><br><br />
Digit 1 - on above figure - indicate embossing, which can be cutted and after it create four holes for screwing doorphone casing to wall or pillar, where it should be assembled. Assembly can be done using appropriate screws &Phi;6, not included in doorphone set.<br />
Over-plaster assembly is not recommended if doorphone is located on wall or pillar outside the building. In this stituation it is recommended to use special protection casing, protecting doorphone against results of rain- and snow-fall. This casing - it is separate position in price list - is sold with three screws for plastic 3,1x13, which enable to fix this casing to doorphone backside. Shape and dimensions of this casing are presented in chapter [[Characteristic of Slican DPH doorphones|2.1 Characteristic of Slican DPH doorphones]]. Fixing of protection casing to doorphone backside can be make using included screws and holes indicated with digit 2 on above figure. Every time during DPH doorphone assembly, before screwing all screws, connecting cables should be bring into the casing via hole indicated with digit 3. Except two mentioned above over-plaster assembly methods, under-plaster assembly is also possible. For under-plaster assembly special aluminium covering frame should be used, this frame is available in Slican offer. Under-plaster DPH doorphone assembly method is presented on following figure:<br />
<center>[[File:DPH pod tynk.png|300px]]</center><br />
In this situation backside of DPH doorphone is screwed to the bacside of the wall niche. Symilarly as for over-plaster assembly before screwing all screws, connecting cables should be bring into the casing via hole indicated with digit 3. Under-plaster assembly is possible using special protection casing. Special protection casing is linked with DPH doorphone casing identically as for over-plaster casing. Assembly method is presented on following figure:<br />
<center>[[File:DPH pod na tynk.png|400px]]</center></div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH16_-_Doorphone_assembly&diff=7506DPH16 - Doorphone assembly2017-07-07T12:40:03Z<p>Grzegorzz: </p>
<hr />
<div>As mentioned above, DPH doorphone is suitable for under- and over-plaster assembly. On following figure, you can see the backside of DPH doorphone casing.<br />
<center>[[File:DPH tyl oznaczenia.png|200px]]</center><br><br />
Digit 1 - on above figure - indicate embossing, which can be cutted and after it create four holes for screwing doorphone casing to wall or pillar, where it should be assembled. Assembly can be done using appropriate screws &Phi;6, not included in doorphone set.<br />
Over-plaster assembly is not recommended if doorphone is located on wall or pillar outside the building. In this stituation it is recommended to use special protection casing made of aluminium and protecting doorphone against results of rain- and snow-fall. This casing - it is separate position in price list - is sold with three screws for plastic 3,1x13, which enable to fix this casing to doorphone backside. Shape and dimensions of this casing are presented in chapter [[Characteristic of Slican DPH doorphones|2.1 Characteristic of Slican DPH doorphones]]. Fixing of protection casing to doorphone backside can be make using included screws and holes indicated with digit 2 on above figure. Every time during DPH doorphone assembly, before screwing all screws, connecting cables should be bring into the casing via hole indicated with digit 3. Except two mentioned above over-plaster assembly methods, under-plaster assembly is also possible. For under-plaster assembly special aluminium covering frame should be used, this frame is available in Slican offer. Under-plaster DPH doorphone assembly method is presented on following figure:<br />
<center>[[File:DPH pod tynk.png|300px]]</center><br />
In this situation backside of DPH doorphone is screwed to the bacside of the wall niche. Symilarly as for over-plaster assembly before screwing all screws, connecting cables should be bring into the casing via hole indicated with digit 3. Under-plaster assembly is possible using special protection casing. Special protection casing is linked with DPH doorphone casing identically as for over-plaster casing. Assembly method is presented on following figure:<br />
<center>[[File:DPH pod na tynk.png|400px]]</center></div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_doorphone&diff=7505DPH.IP doorphone2017-07-07T12:39:00Z<p>Grzegorzz: /* Doorphone assembly */</p>
<hr />
<div><center>[[File:DPH.IP-KS4RF.C.png|200px]] [[File:DPH.IP-KS16RF.C.png|200px]] [[File:DPH.IP-KS1RF.C.png|200px]]</center><br />
<br />
<center>'''Dorphone and RFID reader'''</center><br />
<br />
<center>'''DPH.IP'''</center><br />
<br />
<center>Product manual</center><br />
<br />
<center>Release 1.00</center><br />
<br />
<center>'''Slican Sp. z o.o.'''</center><br />
<br />
<center>[http://www.slican.pl/ www.slican.com] </center><br />
<br />
<center>e-mail: [mailto:office@slican.pl office@slican.pl]</center><br />
<br />
<center>Manufacturer reserves right to make changes without prior notification.</center><br />
<br />
<center>Date of last modification: 2017-06-06</center><br />
<br />
= [[Characteristic of Slican DPH.IP doorphone]] =<br />
<br />
== [[Characteristic and DPH.IP cassettes dimensions]] ==<br />
<br />
==[[DPH.IP Opening housing | Opening doorphone housing]]==<br />
<br />
== [[DPH16 - Doorphone assembly|Doorphone assembly]] ==<br />
===[[DPH16 - Assembly on fence|Fence assembly]]===<br />
<br />
==[[DPH.IP Doorphone keyboard]]==<br />
<br />
== [[DPH.IP Doorphone connection]] ==<br />
<br />
== [[PBX configuration for doorphone operation]] ==<br />
<br />
== [[DPH.IP Doorphone programming]] ==<br />
<br />
== [[DPH16 - Doorphone using|Doorphone using]] ==<br />
<br />
= [[Safety requirements while using DPH series doorphones]] =<br />
<br />
= [[DPH.IP certificate of conformity and proper device disposal]] =</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_Opening_housing&diff=7504DPH.IP Opening housing2017-07-07T12:21:57Z<p>Grzegorzz: </p>
<hr />
<div>DPH.IP front panel is screwed to backside of the housing with M4 allen screw attached in set. Screw lpace is shows with 1 on below drawing.<br />
<br />
Used on drawing signs are explained in below table.<br />
<center><br />
{|{{prettytable}}<br />
!{{Hl2}}|DPH.IP-KS16DRF.C !!{{Hl2}}| DPH.IP-KS4DRF.C !!{{Hl2}}| DPH.IP-KS1RF.C !!{{Hl2}}| DPH.IP-CR0RF<br />
|-<br />
|[[File:DPH.IP-KS16RF.C_signs.png|200px]]||[[File:DPH.IP-KS4RF.C_signs.png|200px]]||[[File:DPH.IP-KS1RF.C_signs.png|200px]]||[[File:DPH.IP-CR0RF_inner.png|200px]]<br />
|-<br />
|1. Mounting screws||1. Mounting screws||1. Mounting screws||1. LED<br />
|-<br />
|2. Speaker||2. Speaker||2. Speaker||2. RFID reader<br />
|-<br />
|3. Camera hole||3. Camera hole||3. Camera hole||3. SETUP jumper<br />
|-<br />
|4. Holes for IR||4. Holes for I||4. Holes for I||4. Mounting holes<br />
|-<br />
|5. LCD display||5. LCD display||5. Button label||<br />
|-<br />
|6. Keypad||6. Navigation buttons||6. Ring button||<br />
|-<br />
|7. Microphone||7. Microphone||7. Microphone||<br />
|}<br />
</center><br />
<br><br />
DPH.IP mainboard is show on below drawing:<br />
<center>[[File:DPH.IP-KS1RF.C_inside.png|200px]]<br />
{|{{prettytable}}<br />
!{{Hl2}}|No !!{{Hl2}}| Descriptione <br />
|-<br />
|1||Place for camera module with IR<br />
|-<br />
|2||Button label (for DPH.IP-KS1RFC)<br />
|-<br />
|3||Camera plugin<br />
|-<br />
|4||IR plugin<br />
|-<br />
|5||Doorphone speaker plugin<br />
|-<br />
|6||ETH network interface<br />
|-<br />
|7||SETUP jumper<br />
|-<br />
|8||Additional expansion module terminal (WIEGAND)<br />
|-<br />
|9||EZ work mode jumper<br />
|-<br />
|10||Terminals for alternative power supply and adtitional features<br />
|-<br />
|11||Anti sabotage switch<br />
|-<br />
|12||Microphone plugin<br />
|-<br />
|}</center></div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=File:DPH.IP-KS1RF.C_inside.png&diff=7503File:DPH.IP-KS1RF.C inside.png2017-07-07T12:21:31Z<p>Grzegorzz: </p>
<hr />
<div></div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=File:DPH.IP-CR0RF_inner.png&diff=7502File:DPH.IP-CR0RF inner.png2017-07-07T12:21:23Z<p>Grzegorzz: </p>
<hr />
<div></div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=File:DPH.IP-KS1RF.C_signs.png&diff=7501File:DPH.IP-KS1RF.C signs.png2017-07-07T12:21:14Z<p>Grzegorzz: </p>
<hr />
<div></div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=File:DPH.IP-KS4RF.C_signs.png&diff=7500File:DPH.IP-KS4RF.C signs.png2017-07-07T12:21:05Z<p>Grzegorzz: </p>
<hr />
<div></div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=File:DPH.IP-KS16RF.C_signs.png&diff=7499File:DPH.IP-KS16RF.C signs.png2017-07-07T12:20:56Z<p>Grzegorzz: </p>
<hr />
<div></div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_Opening_housing&diff=7498DPH.IP Opening housing2017-07-07T12:19:48Z<p>Grzegorzz: </p>
<hr />
<div>DPH.IP front panel is screwed to backside of the housing with M4 allen screw attached in set. Screw lpace is shows with 1 on below drawing.<br />
<br />
Used on drawing signs are explained in below table.<br />
<center><br />
{|{{prettytable}}<br />
!{{Hl2}}|DPH.IP-KS16DRF.C !!{{Hl2}}| DPH.IP-KS4DRF.C !!{{Hl2}}| DPH.IP-KS1RF.C !!{{Hl2}}| DPH.IP-CR0RF<br />
|-<br />
|[[File:DPH.IP-KS16RF.C_signs.png|200px]]||[[File:DPH.IP-KS4RF.C_signs.png|200px]]||[[File:DPH.IP-KS1RF.C_signs.png|200px]]||[[File:DPH.IP-CR0RF_inner.png|200px]]<br />
|-<br />
|1. Mounting screws||1. Mounting screws||1. Mounting screws||1. LED<br />
|-<br />
|2. Speaker||2. Speaker||2. Speaker||2. RFID reader<br />
|-<br />
|3. Camera hole||3. Camera hole||3. Camera hole||3. SETUP jumper<br />
|-<br />
|4. Holes for IR||4. Holes for I||4. Holes for I||4. Mounting holes<br />
|-<br />
|5. LCD display||5. LCD display||5. Button label||<br />
|-<br />
|6. Keypad||6. Navigation buttons||6. Ring button||<br />
|-<br />
|7. Microphone||7. Microphone||7. Microphone||<br />
|}<br />
</center><br />
<br><br />
DPH.IP mainboard is show on below drawing:<br />
<center>[[File:DPH.IP-KS1RF.C_inside.png|200px]]<br />
{|{{prettytable}}<br />
!{{Hl2}}|Digit !!{{Hl2}}| Descriptione <br />
|-<br />
|1||Place for camera module with IR<br />
|-<br />
|2||Button label (for DPH.IP-KS1RFC)<br />
|-<br />
|3||Camera plugin<br />
|-<br />
|4||IR plugin<br />
|-<br />
|5||Doorphone speaker plugin<br />
|-<br />
|6||ETH network interface<br />
|-<br />
|7||SETUP jumper<br />
|-<br />
|8||Additional expansion module terminal (WIEGAND)<br />
|-<br />
|9||EZ work mode jumper<br />
|-<br />
|10||Terminals for alternative power supply and adtitional features<br />
|-<br />
|11||Anti sabotage switch<br />
|-<br />
|12||Microphone plugin<br />
|-<br />
|}</center></div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_Opening_housing&diff=7497DPH.IP Opening housing2017-07-07T12:12:41Z<p>Grzegorzz: </p>
<hr />
<div>DPH.IP front panel is screwed to backside of the housing with M4 allen screw attached in set. Screw lpace is shows with 1 on below drawing.<br />
<br />
Used on drawing signs are explained in below table.<br />
<center><br />
{|{{prettytable}}<br />
!{{Hl2}}|DPH.IP-KS16DRF.C !!{{Hl2}}| DPH.IP-KS4DRF.C !!{{Hl2}}| DPH.IP-KS1RF.C !!{{Hl2}}| DPH.IP-CR0RF<br />
|-<br />
|[[File:DPH.IP-KS16RF.C_signs.png|200px]]||[[File:DPH.IP-KS4RF.C_signs.png|200px]]||[[File:DPH.IP-KS1RF.C_signs.png|200px]]||[[File:DPH.IP-CR0RF_inner.png|200px]]<br />
|-<br />
|1. Sruby montażowe||1. Śruby montażowe||1. Śruby montażowe||1. Dioda LED<br />
|-<br />
|2. Głośnik||2. Głośnik||2. Głośnik||2. Czytnik RFID<br />
|-<br />
|3. Otwór na kamerę||3. Otwór na kamerę||3. Otwór na kamerę||3. Zwora SETUP<br />
|-<br />
|4. Otwory na diody doświetlajace||4. Otwory na diody doświetlajace||4. Otwory na diody doświetlajace||4. Otwory montażowe<br />
|-<br />
|5. Wyświetlacz LCD||5. Wyświetlacz LCD||5. Kartka opisowa dla przycisku||<br />
|-<br />
|6. Klawiatura||6. Przyciski nawigacyjne||6. Klawisz wywołania||<br />
|-<br />
|7. Mikrofon||7. Mikrofon||7. Mikrofon||<br />
|}<br />
</center><br />
<br><br />
Widok płytki elektroniki przykręconej do panelu przedniego prezentuje poniższy rysunek:<br />
<center>[[File:DPH.IP-KS1RF.C_inside.png|200px]]<br />
{|{{prettytable}}<br />
!{{Hl2}}|Cyfra !!{{Hl2}}| Znaczenie <br />
|-<br />
|1||Obszar dla adaptera kamery z podświetleniem<br />
|-<br />
|2||Kartka opisowa<br />
|-<br />
|3||Złącze do podłączenia kamery<br />
|-<br />
|4||Złącze zasilania doświetlenia kamery<br />
|-<br />
|5||Złącze głośnika bramofonu<br />
|-<br />
|6||Interfejs sieciowy bramofonu<br />
|-<br />
|7||Zworka SETUP<br />
|-<br />
|8||Złącze opcjonalnych modułów rozszerzeń (Wiegand)<br />
|-<br />
|9||Zworka przełączająca tryby pracy wyjścia EZ<br />
|-<br />
|10||Złącza do podłączenia bramofonu<br />
|-<br />
|11||Przełącznik antysabotażowy<br />
|-<br />
|12||Złącze mikrofonu<br />
|-<br />
|}</center></div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=Characteristic_and_DPH.IP_cassettes_dimensions&diff=7496Characteristic and DPH.IP cassettes dimensions2017-07-07T12:06:00Z<p>Grzegorzz: </p>
<hr />
<div>=DPH.IP-KSxxRFC=<br />
KS cassettes used in DPH doorphones are executed from special plastic and can be equipped with decorative elements made from stainless steel. They can be adapted to over- and under-plaster assembly. On presented below figures you can see dimensions of cassettes and other elements used for doorphone assembly:<br />
<center>[[File:DPH_wymiary.png|350px]]</center><br><br />
With over-plaster assembly, it is possible to use aluminium protection casing, which protects doorphone against rain- and snowfall. Following figures presents dimensions of mentioned protection casing:<br />
<center>[[File:KS.C93N-INOX_wymiary.png|350px]]</center><br><br />
Next figure presents dimensions of frame, which can be used for under-plaster assembly. There are twotypes of frame types, from stainless steel and black pleksy (depth 3mm):<br />
<center>[[File:KS.F-INOX_wymiary_1.png|350px]]</center><br><br />
Possible is also using frame together with aluminium protection casing. Such solution enables to under-plaster assembly and protects doorphone against rain- and snowfall. Following figure presents dimensions of elemets used for this solution:<br />
<center>[[File:KS.C93P-INOX_wymiary.png|500px]]</center><br><br />
To mount doorphone on a fence, use cassete presented below.<br />
<center>[[File:KS.C120N-INOX_wymiary.png|350px]]</center><br><br />
=DPH.IP-CR0RF=<br />
Proximity card reader is produced from platic and its designed for on wall mounting.<br />
<center>[[File:DPH_dimensions.png]]</center><br></div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=Characteristic_of_Slican_DPH.IP_doorphone&diff=7495Characteristic of Slican DPH.IP doorphone2017-07-07T11:50:10Z<p>Grzegorzz: /* Maximum devices used depending on PBX type */</p>
<hr />
<div>Slican DPH.IP doorphone series connected to PBX enables to establish call between person near doorphone and PBX subscriber, as well as enter to protected area. It is also possible to trigger an electrolock, for opening door or gate, from phone connected to PBX.<br><br />
Additionally, DPH.IP doorphone can be used as fully functional access control system (ACS), due to registered events, that are send and visible in detailed billing application, or application designed especially for individual client. Thanks to installed, doorphone can control two relays (e.g. gate or doors), detect door opening or additional button pressing.<br><br />
Slican offers three types or DPH.IP-KSxxRF.C devices:<br />
<br><br><br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>DEVICE MODEL</b></center> !!{{Hl1}}|<center><b>FEATURES</b></center><br />
|-<br />
| <center><b>DPH.IP-CR0RF</b></center> ||<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
** RFID card/pendant reader<br />
** one relay (EZ)<br />
** door opened sensor and button (COD, POD)<br />
* powered directly with PoE<br />
** RFID card/pendant reader<br />
<br />
|-<br />
| <center><b>DPH.IP-KS1RF.C</b></center> ||<br />
* doorphone with one call key<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
<br />
|-<br />
| <center><b>DPH.IP-KS4DRF.C</b></center> ||<br />
* doorphone with four keys (two navigational, one answering and one dismissing a call)<br />
* LCD display for showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
<br />
|-<br />
| <center><b>DPH.IP-KS16DRF.C</b></center> ||<br />
* doorphone with full alphanumeric keyboard<br />
* LCD display for configuring the device and showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
|}<br />
<br />
<br />
Following functions are available in DPH.IP doorphone (varies, depending on DPH model):<br />
* establish phone call using touch buttons arranged in form of numeric keyboard<br />
* two relays trigger:<br />
** electrolock (EZ)<br />
** additional relay (STA)<br />
* power supply with 12-25V AC lub 14-35V DC or PoE<br />
* environment temperature range -20 to +70 (below 0 degrees, display reating time increases up to 10 seconds)<br />
* inputs COD (opening door sensori) i POD (opening door button). Both buttons operate with electrolock.<br />
* EZ trigger (opening) by receiving '''„1”''' or '''„*”''' character in DTMF code<br />
* built-in RFID card reader (Unique 125kHz standard, in accordance with EM4102)<br />
* possibility to trigger EZ or STA by registered RFID card approach<br />
* STA trigger (second relay) by receiving '''"2"''' character in DTMF code. Single pulse with fixed duration time is generated<br />
* graphical LCD display (except DPH.IP-KS1RF.C)<br />
<br />
=Maximum devices used depending on PBX type=<br />
<br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>PBX TYPE</b></center> !!{{Hl1}}|<center><b>DPH.IP</b></center><br />
|-<br />
| <center>IPL-256</center>||<center>99</center><br />
|-<br />
| <center>IPM-032</center> ||<center>99</center><br />
|-<br />
| <center>IPM-032.LowCost</center> ||<center>10</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>28</center><br />
|-<br />
| <center>IPU-14.102</center> ||<center>68</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.100,101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.104.105<br>(LowCost)</center> ||<center>8</center><br />
|-<br />
| <center>MAC-6400</center> ||<center>99</center><br />
|-<br />
| <center>CCT-1668</center> ||<center>60</center><br />
|}<br />
<br />
=Mounting=<br />
All DPH and DPH.IP-KSxxRFC series doorphones are manufactured in various designs and depending on the implementation, they can be installed<br />
* as over-plaster<br />
* as under-plaster<br />
* on the fence</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_doorphone&diff=7494DPH.IP doorphone2017-07-07T11:49:44Z<p>Grzegorzz: </p>
<hr />
<div><center>[[File:DPH.IP-KS4RF.C.png|200px]] [[File:DPH.IP-KS16RF.C.png|200px]] [[File:DPH.IP-KS1RF.C.png|200px]]</center><br />
<br />
<center>'''Dorphone and RFID reader'''</center><br />
<br />
<center>'''DPH.IP'''</center><br />
<br />
<center>Product manual</center><br />
<br />
<center>Release 1.00</center><br />
<br />
<center>'''Slican Sp. z o.o.'''</center><br />
<br />
<center>[http://www.slican.pl/ www.slican.com] </center><br />
<br />
<center>e-mail: [mailto:office@slican.pl office@slican.pl]</center><br />
<br />
<center>Manufacturer reserves right to make changes without prior notification.</center><br />
<br />
<center>Date of last modification: 2017-06-06</center><br />
<br />
= [[Characteristic of Slican DPH.IP doorphone]] =<br />
<br />
== [[Characteristic and DPH.IP cassettes dimensions]] ==<br />
<br />
==[[DPH.IP Opening housing | Opening doorphone housing]]==<br />
<br />
== [[DPH16 - Doorphone assembly|Doorphone assembly]] ==<br />
<br />
===[[DPH16 - Over-plaster or under-plaster assembly|Over-plaster or under-plaster assembly]]===<br />
<br />
===[[DPH16 - Assembly on fence|Fence assembly]]===<br />
<br />
==[[DPH.IP Doorphone keyboard]]==<br />
<br />
== [[DPH.IP Doorphone connection]] ==<br />
<br />
== [[PBX configuration for doorphone operation]] ==<br />
<br />
== [[DPH.IP Doorphone programming]] ==<br />
<br />
== [[DPH16 - Doorphone using|Doorphone using]] ==<br />
<br />
= [[Safety requirements while using DPH series doorphones]] =<br />
<br />
= [[DPH.IP certificate of conformity and proper device disposal]] =</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=Characteristic_of_Slican_DPH.IP_doorphone&diff=7493Characteristic of Slican DPH.IP doorphone2017-07-07T11:47:16Z<p>Grzegorzz: </p>
<hr />
<div>Slican DPH.IP doorphone series connected to PBX enables to establish call between person near doorphone and PBX subscriber, as well as enter to protected area. It is also possible to trigger an electrolock, for opening door or gate, from phone connected to PBX.<br><br />
Additionally, DPH.IP doorphone can be used as fully functional access control system (ACS), due to registered events, that are send and visible in detailed billing application, or application designed especially for individual client. Thanks to installed, doorphone can control two relays (e.g. gate or doors), detect door opening or additional button pressing.<br><br />
Slican offers three types or DPH.IP-KSxxRF.C devices:<br />
<br><br><br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>DEVICE MODEL</b></center> !!{{Hl1}}|<center><b>FEATURES</b></center><br />
|-<br />
| <center><b>DPH.IP-CR0RF</b></center> ||<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
** RFID card/pendant reader<br />
** one relay (EZ)<br />
** door opened sensor and button (COD, POD)<br />
* powered directly with PoE<br />
** RFID card/pendant reader<br />
<br />
|-<br />
| <center><b>DPH.IP-KS1RF.C</b></center> ||<br />
* doorphone with one call key<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
<br />
|-<br />
| <center><b>DPH.IP-KS4DRF.C</b></center> ||<br />
* doorphone with four keys (two navigational, one answering and one dismissing a call)<br />
* LCD display for showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with a power adapter or PoE, using Splitter UCS-CR<br />
<br />
|-<br />
| <center><b>DPH.IP-KS16DRF.C</b></center> ||<br />
* doorphone with full alphanumeric keyboard<br />
* LCD display for configuring the device and showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
|}<br />
<br />
<br />
Following functions are available in DPH.IP doorphone (varies, depending on DPH model):<br />
* establish phone call using touch buttons arranged in form of numeric keyboard<br />
* two relays trigger:<br />
** electrolock (EZ)<br />
** additional relay (STA)<br />
* power supply with 12-25V AC lub 14-35V DC or PoE<br />
* environment temperature range -20 to +70 (below 0 degrees, display reating time increases up to 10 seconds)<br />
* inputs COD (opening door sensori) i POD (opening door button). Both buttons operate with electrolock.<br />
* EZ trigger (opening) by receiving '''„1”''' or '''„*”''' character in DTMF code<br />
* built-in RFID card reader (Unique 125kHz standard, in accordance with EM4102)<br />
* possibility to trigger EZ or STA by registered RFID card approach<br />
* STA trigger (second relay) by receiving '''"2"''' character in DTMF code. Single pulse with fixed duration time is generated<br />
* graphical LCD display (except DPH.IP-KS1RF.C)<br />
<br />
=Maximum devices used depending on PBX type=<br />
{{Warning|DPH.IP, Audio.IP and CTS.IP resources in PBXes are shared.}}<br />
<br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>PBX TYPE</b></center> !!{{Hl1}}|<center><b>DPH.IP</b></center><br />
|-<br />
| <center>IPL-256</center>||<center>99</center><br />
|-<br />
| <center>IPM-032</center> ||<center>99</center><br />
|-<br />
| <center>IPM-032.LowCost</center> ||<center>10</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>28</center><br />
|-<br />
| <center>IPU-14.102</center> ||<center>68</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.100,101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.104.105<br>(LowCost)</center> ||<center>8</center><br />
|-<br />
| <center>MAC-6400</center> ||<center>99</center><br />
|-<br />
| <center>CCT-1668</center> ||<center>60</center><br />
|}</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH16_-_Doorphone_using&diff=7492DPH16 - Doorphone using2017-07-07T09:30:10Z<p>Grzegorzz: </p>
<hr />
<div>DPH-16 user can perform following actions:<br />
* Establish call with any subscriber after dialing extension number of this subscriber<br />
* Trigger relay output of doorphpone<br />
* Anwer incoming calls from any extension number<br />
To establish call with any extension number appropriate number should be dialed from doorphone keyboard and press [[File:DPH16-call.PNG|30px]] button. Caption "Call <dialed extension number>" is visible and message "Please wait for connection" and next melody defined as MOH can be hear in doorphone speaker. After lifting handset of phone with dialed extension number call is established automatically.<br />
<br />
To trigger relay output following activities should be performed:<br />
* Select from keyboard number of defined user<br />
* Press button [[File:DPH16-Kluczyk.PNG|30px]] - on display caption "Enter PIN" is visible<br />
* Enter PIN code defined for specified user account - caption "OPEN", is s visible on display, simultaneously action defined as "PIN enter action" is performed.<br />
<br />
It is possible to trigger relay output by approaching RFID card to doorphone - caption "OPEN" is visible on display, simultanoeusly action defined as "RFID action" is performed.<br />
<br />
If PBX subscriber dial extension number assigned to doorphone, call is established automatically, which is confirmed with caption "Incoming call". In this status conversation between phone and doorphone. Finishing call takes place after hang off handset or pressing [[File:DPH16-end.PNG|30px]] button on doorphone keyboard.<br />
<br />
=Error codes=<br />
In case of any problem with the device operation, doorphone/reader will signalize this fact with a error code visible on display or by keypad or LED signals.<br />
<br />
{|{{prettytable}}<br />
!{{Hl2}}|Error code !!{{Hl2}}|Cause<br />
|-<br />
|11||Awaiting authorization / connection attempt<br />
|-<br />
|13||No IP configuration found<br />
|-<br />
|14||No response from PBX<br />
|-<br />
|15||Unresolved domain name by DNS server<br />
|-<br />
|16||No response from DNS server<br />
|-<br />
|21||No response from DHCP server<br />
|-<br />
|22||No VoIP servers in configured network<br />
|-<br />
|23||PBX reboot<br />
|-<br />
|24||No authorization<br />
|-<br />
|25||Disconnection from PBX<br />
|-<br />
|27||Improper PBX firmware version<br />
|-<br />
|28||Critical error, rebooting device<br />
|-<br />
|51<br>52<br>53<br>54<br>55<br>56<br>57||Hardware error codes - please contact service company<br />
|-<br />
|}<br />
<br><br><br />
Error signalling in devices without display (with keypad backlit or LED):<br><br />
Blinks (number of blinks represents first digit) + short break (1,5s) + Blinks (second digit) + long break (4,5s)<br><br />
then the procedure of signalling start over.</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_Doorphone_programming&diff=7491DPH.IP Doorphone programming2017-07-07T09:28:19Z<p>Grzegorzz: /* Manually configure VoIP server address */</p>
<hr />
<div>Basic DPH.IP-KS16DRF.C doorphone configuration (IP address, VoIP server) can be made by built-in Menu, with display and keyboard. Detailed configuration of the device is made only with a application for PBX configuration, to which we connect the doorphone.<br><br />
Entering the Menu is made by double pressing the [[File:DPH16-Kluczyk.PNG|30px]] key on doorphone’s keyboard on not configured device (not connected to any PBX).<br />
<br />
=PIN code=<br />
DPH.IP-KS16DRF.C doorphone can be assigned with a PIN code, that allows to enter doorphone's Menu. PIN code in not set by deafult. It can be set in PBX configuration application.<br />
{{warning|Turning the doorphone on with short circiuted SETUP jumpers will change the settings to default (factory reset), and deleting the PIN code.}}<br />
<br />
=Doorphone IP configuration=<br />
DPH.IP doorphone configuration is basically simple and it comes down to connecting doorphone to network, adding it and configuring in PBX management application.<br><br />
When doorphone will be used in not standard network environment or e.g will be used in routed network (from Internet), additional configuration will be required. For DPH.IP Doorphone to work correctly in such conditions, it is necessary to:<br />
<br />
==Manually configure doorphone's IP address==<br />
By entering the Menu with double click the [[File:DPH16-Kluczyk.PNG|30px]] key, and choosing <b>VoIP</b> and <b>IP Configuration</b>, using arrows ↓ and ↑, we select, if doorphone should use IP address form DHCP server, or manually configured. Highlighting the options (IP address, Netmask, Gateway) and clicking OK will display used parameters. If we are using manual settings, it will be possible to change those values with keyboard. Trying to change those values, while DHCP client is turned on, will result in dislplaying proper notice.<br />
<br />
==Manually configure VoIP server address==<br />
VoIP server is configured in Menu, after selecting <b>VoIP</b> and next <b>VoIP server</b>. Doorphone can automatically connect to a PBX, which has such equipment already configured, or by manually enterind Domain or IP address.<br><br />
Device authorization is made based on MAC address.<br />
{{warning|MAC address configured in multiple PBXes will result in situation, that when DPH will automatically search for VoIP server, it will connect to a random PBX.}}<br />
If we choose NO, while asked about automatical VoIP server search, with keyboard, we can enter Domain or IP address of VoIP server. Changing the method of input, from letters and digits to digits alone, is made with [[File:DPH16-Kluczyk.PNG|30px]] key during typing the address.<br />
{{warning|After setting the doorphone from Menu, further configuration is possible only from application for PBX configuration.<br>Check changes made in PBX application that regard DPH.IP configuration. Improper parameters can result in disconnecting doorphone from PBX. Manual changes (locally from DPH.IP mennu) will be needed.}}<br />
Changing DPH.IP configuration from PBX application, while it is disconnected, will result, that, after restoring connection, doorphone configuration will overwrite configuration made in PBX application.<br />
<br />
=DPH.IP-CR0RF and DPH.IP-KSxRF.C=<br />
When turning on a doorphone without alphanumeric keyboard, DHCP client and automatic VoIP server searching features are on. After connecting the doorphone to the same network as PBX, it will be possible to configure the device from PBX configuration application and therefore changing its IP address.<br><br />
Doorphone authorization is based on MAC address matching, so it will be necessary to accept a device in PBX.<br><br />
This series doorphones do not allow for configuration directly in the device.</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_Doorphone_programming&diff=7490DPH.IP Doorphone programming2017-07-07T09:23:39Z<p>Grzegorzz: /* Manually configure VoIP server address */</p>
<hr />
<div>Basic DPH.IP-KS16DRF.C doorphone configuration (IP address, VoIP server) can be made by built-in Menu, with display and keyboard. Detailed configuration of the device is made only with a application for PBX configuration, to which we connect the doorphone.<br><br />
Entering the Menu is made by double pressing the [[File:DPH16-Kluczyk.PNG|30px]] key on doorphone’s keyboard on not configured device (not connected to any PBX).<br />
<br />
=PIN code=<br />
DPH.IP-KS16DRF.C doorphone can be assigned with a PIN code, that allows to enter doorphone's Menu. PIN code in not set by deafult. It can be set in PBX configuration application.<br />
{{warning|Turning the doorphone on with short circiuted SETUP jumpers will change the settings to default (factory reset), and deleting the PIN code.}}<br />
<br />
=Doorphone IP configuration=<br />
DPH.IP doorphone configuration is basically simple and it comes down to connecting doorphone to network, adding it and configuring in PBX management application.<br><br />
When doorphone will be used in not standard network environment or e.g will be used in routed network (from Internet), additional configuration will be required. For DPH.IP Doorphone to work correctly in such conditions, it is necessary to:<br />
<br />
==Manually configure doorphone's IP address==<br />
By entering the Menu with double click the [[File:DPH16-Kluczyk.PNG|30px]] key, and choosing <b>VoIP</b> and <b>IP Configuration</b>, using arrows ↓ and ↑, we select, if doorphone should use IP address form DHCP server, or manually configured. Highlighting the options (IP address, Netmask, Gateway) and clicking OK will display used parameters. If we are using manual settings, it will be possible to change those values with keyboard. Trying to change those values, while DHCP client is turned on, will result in dislplaying proper notice.<br />
<br />
==Manually configure VoIP server address==<br />
VoIP server is configured in Menu, after selecting <b>VoIP</b> and next <b>VoIP server</b>. Doorphone can automatically connect to a PBX, which has such equipment already configured, or by manually enterind Domain or IP address.<br><br />
Device authorization is made based on MAC address.<br />
{{warning|MAC address configured in multiple PBXes will result in situation, that when DPH will automatically search for VoIP server, it will connect to a random PBX.}}<br />
If we choose NO, while asked about automatical VoIP server search, with keyboard, we can enter Domain or IP address of VoIP server. Changing the method of input, from letters and digits to digits alone, is made with [[File:DPH16-Kluczyk.PNG|30px]] key during typing the address.<br />
{{warning|After setting the doorphone from Menu, further configuration is possible only from application for PBX configuration.<br>Check changes made in PBX application that regard DPH.IP configuration. Improper parameters can result in disconnecting doorphone from PBX. Manual changes (locally from DPH.IP mennu) will be needed.}}<br />
<br />
=DPH.IP-CR0RF and DPH.IP-KSxRF.C=<br />
When turning on a doorphone without alphanumeric keyboard, DHCP client and automatic VoIP server searching features are on. After connecting the doorphone to the same network as PBX, it will be possible to configure the device from PBX configuration application and therefore changing its IP address.<br><br />
Doorphone authorization is based on MAC address matching, so it will be necessary to accept a device in PBX.<br><br />
This series doorphones do not allow for configuration directly in the device.</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_Doorphone_programming&diff=7489DPH.IP Doorphone programming2017-07-07T09:23:23Z<p>Grzegorzz: /* Manually configure VoIP server address */</p>
<hr />
<div>Basic DPH.IP-KS16DRF.C doorphone configuration (IP address, VoIP server) can be made by built-in Menu, with display and keyboard. Detailed configuration of the device is made only with a application for PBX configuration, to which we connect the doorphone.<br><br />
Entering the Menu is made by double pressing the [[File:DPH16-Kluczyk.PNG|30px]] key on doorphone’s keyboard on not configured device (not connected to any PBX).<br />
<br />
=PIN code=<br />
DPH.IP-KS16DRF.C doorphone can be assigned with a PIN code, that allows to enter doorphone's Menu. PIN code in not set by deafult. It can be set in PBX configuration application.<br />
{{warning|Turning the doorphone on with short circiuted SETUP jumpers will change the settings to default (factory reset), and deleting the PIN code.}}<br />
<br />
=Doorphone IP configuration=<br />
DPH.IP doorphone configuration is basically simple and it comes down to connecting doorphone to network, adding it and configuring in PBX management application.<br><br />
When doorphone will be used in not standard network environment or e.g will be used in routed network (from Internet), additional configuration will be required. For DPH.IP Doorphone to work correctly in such conditions, it is necessary to:<br />
<br />
==Manually configure doorphone's IP address==<br />
By entering the Menu with double click the [[File:DPH16-Kluczyk.PNG|30px]] key, and choosing <b>VoIP</b> and <b>IP Configuration</b>, using arrows ↓ and ↑, we select, if doorphone should use IP address form DHCP server, or manually configured. Highlighting the options (IP address, Netmask, Gateway) and clicking OK will display used parameters. If we are using manual settings, it will be possible to change those values with keyboard. Trying to change those values, while DHCP client is turned on, will result in dislplaying proper notice.<br />
<br />
==Manually configure VoIP server address==<br />
VoIP server is configured in Menu, after selecting <b>VoIP</b> and next <b>VoIP server</b>. Doorphone can automatically connect to a PBX, which has such equipment already configured, or by manually enterind Domain or IP address.<br><br />
Device authorization is made based on MAC address.<br />
{{warning|MAC address configured in multiple PBXes will result in situation, that when DPH will automatically search for VoIP server, it will connect to a random PBX.}}<br />
If we choose NO, while asked about automatical VoIP server search, with keyboard, we can enter Domain or IP address of VoIP server. Changing the method of input, from letters and digits to digits alone, is made with [[File:DPH16-Kluczyk.PNG|30px]] key during typing the address.<br />
{{warning|After setting the doorphone from Menu, further configuration is possible only from application for PBX configuration. Check changes made in PBX application that regard DPH.IP configuration. Improper parameters can result in disconnecting doorphone from PBX. Manual changes (locally from DPH.IP mennu) will be needed.}}<br />
<br />
=DPH.IP-CR0RF and DPH.IP-KSxRF.C=<br />
When turning on a doorphone without alphanumeric keyboard, DHCP client and automatic VoIP server searching features are on. After connecting the doorphone to the same network as PBX, it will be possible to configure the device from PBX configuration application and therefore changing its IP address.<br><br />
Doorphone authorization is based on MAC address matching, so it will be necessary to accept a device in PBX.<br><br />
This series doorphones do not allow for configuration directly in the device.</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_Doorphone_programming&diff=7488DPH.IP Doorphone programming2017-07-07T09:18:02Z<p>Grzegorzz: /* Doorphone IP configuration */</p>
<hr />
<div>Basic DPH.IP-KS16DRF.C doorphone configuration (IP address, VoIP server) can be made by built-in Menu, with display and keyboard. Detailed configuration of the device is made only with a application for PBX configuration, to which we connect the doorphone.<br><br />
Entering the Menu is made by double pressing the [[File:DPH16-Kluczyk.PNG|30px]] key on doorphone’s keyboard on not configured device (not connected to any PBX).<br />
<br />
=PIN code=<br />
DPH.IP-KS16DRF.C doorphone can be assigned with a PIN code, that allows to enter doorphone's Menu. PIN code in not set by deafult. It can be set in PBX configuration application.<br />
{{warning|Turning the doorphone on with short circiuted SETUP jumpers will change the settings to default (factory reset), and deleting the PIN code.}}<br />
<br />
=Doorphone IP configuration=<br />
DPH.IP doorphone configuration is basically simple and it comes down to connecting doorphone to network, adding it and configuring in PBX management application.<br><br />
When doorphone will be used in not standard network environment or e.g will be used in routed network (from Internet), additional configuration will be required. For DPH.IP Doorphone to work correctly in such conditions, it is necessary to:<br />
<br />
==Manually configure doorphone's IP address==<br />
By entering the Menu with double click the [[File:DPH16-Kluczyk.PNG|30px]] key, and choosing <b>VoIP</b> and <b>IP Configuration</b>, using arrows ↓ and ↑, we select, if doorphone should use IP address form DHCP server, or manually configured. Highlighting the options (IP address, Netmask, Gateway) and clicking OK will display used parameters. If we are using manual settings, it will be possible to change those values with keyboard. Trying to change those values, while DHCP client is turned on, will result in dislplaying proper notice.<br />
<br />
==Manually configure VoIP server address==<br />
VoIP server is configured in Menu, after selecting <b>VoIP</b> and next <b>VoIP server</b>. Doorphone can automatically connect to a PBX, which has such equipment already configured, or by manually enterind Domain or IP address.<br><br />
Device authorization is made based on MAC address.<br />
{{warning|MAC address configured in multiple PBXes will result in situation, that when DPH will automatically search for VoIP server, it will connect to a random PBX.}}<br />
If we choose NO, while asked about automatical VoIP server search, with keyboard, we can enter Domain or IP address of VoIP server. Changing the method of input, from letters and digits to digits alone, is made with [[File:DPH16-Kluczyk.PNG|30px]] key during typing the address.<br />
{{warning|After setting the doorphone from Menu, further configuration is possible only from application for PBX configuration.}}<br />
<br />
=DPH.IP-CR0RF and DPH.IP-KSxRF.C=<br />
When turning on a doorphone without alphanumeric keyboard, DHCP client and automatic VoIP server searching features are on. After connecting the doorphone to the same network as PBX, it will be possible to configure the device from PBX configuration application and therefore changing its IP address.<br><br />
Doorphone authorization is based on MAC address matching, so it will be necessary to accept a device in PBX.<br><br />
This series doorphones do not allow for configuration directly in the device.</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_Doorphone_programming&diff=7487DPH.IP Doorphone programming2017-07-07T09:05:29Z<p>Grzegorzz: /* PIN code */</p>
<hr />
<div>Basic DPH.IP-KS16DRF.C doorphone configuration (IP address, VoIP server) can be made by built-in Menu, with display and keyboard. Detailed configuration of the device is made only with a application for PBX configuration, to which we connect the doorphone.<br><br />
Entering the Menu is made by double pressing the [[File:DPH16-Kluczyk.PNG|30px]] key on doorphone’s keyboard on not configured device (not connected to any PBX).<br />
<br />
=PIN code=<br />
DPH.IP-KS16DRF.C doorphone can be assigned with a PIN code, that allows to enter doorphone's Menu. PIN code in not set by deafult. It can be set in PBX configuration application.<br />
{{warning|Turning the doorphone on with short circiuted SETUP jumpers will change the settings to default (factory reset), and deleting the PIN code.}}<br />
<br />
=Doorphone IP configuration=<br />
For DPH.IP Doorphone to work correctly, it is necessary to:<br />
<br />
==Doorphone IP address configuration==<br />
By entering the Menu with double click the [[File:DPH16-Kluczyk.PNG|30px]] key, and choosing <b>VoIP</b> and <b>IP Configuration</b>, using arrows ↓ and ↑, we select, if doorphone should use IP address form DHCP server, or manually configured. Highlighting the options (IP address, Netmask, Gateway) and clicking OK will display used parameters. If we are using manual settings, it will be possible to change those values with keyboard. Trying to change those values, while DHCP client is turned on, will result in dislplaying proper notice.<br />
<br />
==VoIP server configuration==<br />
VoIP server is configured in Menu, after selecting <b>VoIP</b> and next <b>VoIP server</b>. Doorphone can automatically connect to a PBX, which has such equipment already configured, or by manually enterind Domain or IP address.<br><br />
Device authorization is made based on MAC address.<br />
{{warning|MAC address configured in multiple PBXes will result in situation, that when DPH will automatically search for VoIP server, it will connect to a random PBX.}}<br />
If we choose NO, while asked about automatical VoIP server search, with keyboard, we can enter Domain or IP address of VoIP server. Changing the method of input, from letters and digits to digits alone, is made with [[File:DPH16-Kluczyk.PNG|30px]] key during typing the address.<br />
{{warning|After setting the doorphone from Menu, further configuration is possible only from application for PBX configuration.}}<br />
<br />
=DPH.IP-CR0RF and DPH.IP-KSxRF.C=<br />
When turning on a doorphone without alphanumeric keyboard, DHCP client and automatic VoIP server searching features are on. After connecting the doorphone to the same network as PBX, it will be possible to configure the device from PBX configuration application and therefore changing its IP address.<br><br />
Doorphone authorization is based on MAC address matching, so it will be necessary to accept a device in PBX.<br><br />
This series doorphones do not allow for configuration directly in the device.</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_Doorphone_programming&diff=7486DPH.IP Doorphone programming2017-07-07T09:03:51Z<p>Grzegorzz: /* PIN code */</p>
<hr />
<div>Basic DPH.IP-KS16DRF.C doorphone configuration (IP address, VoIP server) can be made by built-in Menu, with display and keyboard. Detailed configuration of the device is made only with a application for PBX configuration, to which we connect the doorphone.<br><br />
Entering the Menu is made by double pressing the [[File:DPH16-Kluczyk.PNG|30px]] key on doorphone’s keyboard on not configured device (not connected to any PBX).<br />
<br />
=PIN code=<br />
DPH.IP-KS16DRF.C doorphone can be assigned with a PIN code, that allows to enter programming Menu and change IP interface and VoIP server settings. PIN code in not set by deafult, and its used for entering doorphone menu.<br />
{{warning|Turning the doorphone on with short circiuted SETUP jumpers will change the settings to default (factory reset), and deleting the PIN code.}}<br />
<br />
=Doorphone IP configuration=<br />
For DPH.IP Doorphone to work correctly, it is necessary to:<br />
<br />
==Doorphone IP address configuration==<br />
By entering the Menu with double click the [[File:DPH16-Kluczyk.PNG|30px]] key, and choosing <b>VoIP</b> and <b>IP Configuration</b>, using arrows ↓ and ↑, we select, if doorphone should use IP address form DHCP server, or manually configured. Highlighting the options (IP address, Netmask, Gateway) and clicking OK will display used parameters. If we are using manual settings, it will be possible to change those values with keyboard. Trying to change those values, while DHCP client is turned on, will result in dislplaying proper notice.<br />
<br />
==VoIP server configuration==<br />
VoIP server is configured in Menu, after selecting <b>VoIP</b> and next <b>VoIP server</b>. Doorphone can automatically connect to a PBX, which has such equipment already configured, or by manually enterind Domain or IP address.<br><br />
Device authorization is made based on MAC address.<br />
{{warning|MAC address configured in multiple PBXes will result in situation, that when DPH will automatically search for VoIP server, it will connect to a random PBX.}}<br />
If we choose NO, while asked about automatical VoIP server search, with keyboard, we can enter Domain or IP address of VoIP server. Changing the method of input, from letters and digits to digits alone, is made with [[File:DPH16-Kluczyk.PNG|30px]] key during typing the address.<br />
{{warning|After setting the doorphone from Menu, further configuration is possible only from application for PBX configuration.}}<br />
<br />
=DPH.IP-CR0RF and DPH.IP-KSxRF.C=<br />
When turning on a doorphone without alphanumeric keyboard, DHCP client and automatic VoIP server searching features are on. After connecting the doorphone to the same network as PBX, it will be possible to configure the device from PBX configuration application and therefore changing its IP address.<br><br />
Doorphone authorization is based on MAC address matching, so it will be necessary to accept a device in PBX.<br><br />
This series doorphones do not allow for configuration directly in the device.</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=DPH.IP_Doorphone_keyboard&diff=7485DPH.IP Doorphone keyboard2017-07-07T09:02:27Z<p>Grzegorzz: </p>
<hr />
<div>Doorphone keyboard layout is presented in chapter [[DPH16 - Opening doorphone casing|Opening doorphone casing]]. <br />
In this chapter you can find detailed description of only two elements presented in chapter [[DPH16 - Opening doorphone casing|Opening doorphone casing]] and included in doorphone front panel - LCD display and keyboard.<br />
* • LCD display present in DPH.IP-KS16DRF.C and DPH.IP-KS4DRF.C is used for presenting data entered by user from keyboard and activities performed by doorphone as a result of these entering. Graphical display is used in DPH.IP with resolution of 113x32 pixels. Depending on character quantity, font size can be increased or reduced for properly showing all of necessary text.<br />
* Keyboard include following touch buttons:<br />
** Buttons with digit [[File:DPH16-Cyfra 0.PNG|30px]]...[[File:DPH16-Cyfra 9.PNG|30px]] (not present in DPH.IP-KS4DRF.C)<br />
** Function button [[File:DPH16-Kluczyk.PNG|30px]] (not present in DPH.IP-KS4DRF.C)<br />
** Delete button [[File:DPH16-C.PNG|30px]] (not present in DPH.IP-KS4DRF.C)<br />
** Navigation cuttons [[File:DPH16-Up.PNG|30px]] and [[File:DPH16-Down.PNG|34px]]<br />
** Call button [[File:DPH16-call.PNG|30px]]<br />
** Finishing button [[File:DPH16-end.PNG|30px]]<br />
Keyboard together with LCD display enable both - establishing call and doorphone programming. It should be noticed, that DPH doorphone can be program in two ways:<br />
* Connection (IP address, VoIP server), from DPH Menu<br />
* With application for PBX configuration.<br />
* Local, for network parameters configuration (IP address, VoIP server address) - from doorphone menu<br />
* Remote, for detailed doorphone operation configuration - with PBX configuration application.</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=Characteristic_of_Slican_DPH.IP_doorphone&diff=7484Characteristic of Slican DPH.IP doorphone2017-07-07T08:57:51Z<p>Grzegorzz: </p>
<hr />
<div>Slican DPH.IP doorphone series connected to PBX enables to establish call between person near doorphone and PBX subscriber, as well as enter to protected area. It is also possible to trigger an electrolock, for opening door or gate, from phone connected to PBX.<br><br />
Additionally, DPH.IP doorphone can be used as fully functional access control system (ACS), due to registered events, that are send and visible in detailed billing application, or application designed especially for individual client. Thanks to installed, doorphone can control two relays (e.g. gate or doors), detect door opening or additional button pressing.<br><br />
Slican offers three types or DPH.IP-KSxxRF.C devices:<br />
<br><br><br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>DEVICE MODEL</b></center> !!{{Hl1}}|<center><b>FEATURES</b></center><br />
|-<br />
| <center><b>DPH.IP-CR0RF</b></center> ||<br />
* powered with Splitter UCS-CR<br />
* RFID card/pendant reader<br />
* one relay (EZ)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE (just ass ACS, without relay actions)<br />
* without calling feature<br />
<br />
|-<br />
| <center><b>DPH.IP-KS1RF.C</b></center> ||<br />
* doorphone with one call key<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
<br />
|-<br />
| <center><b>DPH.IP-KS4DRF.C</b></center> ||<br />
* doorphone with four keys (two navigational, one answering and one dismissing a call)<br />
* LCD display for showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
<br />
|-<br />
| <center><b>DPH.IP-KS16DRF.C</b></center> ||<br />
* doorphone with full alphanumeric keyboard<br />
* LCD display for configuring the device and showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
|}<br />
<br />
<br />
Following functions are available in DPH.IP doorphone (varies, depending on DPH model):<br />
* establish phone call using touch buttons arranged in form of numeric keyboard<br />
* two relays trigger:<br />
** electrolock (EZ)<br />
** additional relay (STA)<br />
* power supply with 12-25V AC lub 14-35V DC or PoE<br />
* environment temperature range -20 to +70 (below 0 degrees, display reating time increases up to 10 seconds)<br />
* inputs COD (opening door sensori) i POD (opening door button). Both buttons operate with electrolock.<br />
* EZ trigger (opening) by receiving '''„1”''' or '''„*”''' character in DTMF code<br />
* built-in RFID card reader (Unique 125kHz standard, in accordance with EM4102)<br />
* possibility to trigger EZ or STA by registered RFID card approach<br />
* STA trigger (second relay) by receiving '''"2"''' character in DTMF code. Single pulse with fixed duration time is generated<br />
* graphical LCD display (except DPH.IP-KS1RF.C)<br />
<br />
=Maximum devices used depending on PBX type=<br />
{{Warning|DPH.IP, Audio.IP and CTS.IP resources in PBXes are shared.}}<br />
<br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>PBX TYPE</b></center> !!{{Hl1}}|<center><b>DPH.IP</b></center><br />
|-<br />
| <center>IPL-256</center>||<center>99</center><br />
|-<br />
| <center>IPM-032</center> ||<center>99</center><br />
|-<br />
| <center>IPM-032.LowCost</center> ||<center>10</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>28</center><br />
|-<br />
| <center>IPU-14.102</center> ||<center>68</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.100,101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.104.105<br>(LowCost)</center> ||<center>8</center><br />
|-<br />
| <center>MAC-6400</center> ||<center>99</center><br />
|-<br />
| <center>CCT-1668</center> ||<center>60</center><br />
|}</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=Characteristic_of_Slican_DPH.IP_doorphone&diff=7483Characteristic of Slican DPH.IP doorphone2017-06-09T13:35:04Z<p>Grzegorzz: /* Maksymalna ilość zastosowanych urządzeń w zależności od modelu centrali */</p>
<hr />
<div>Slican DPH.IP doorphone series connected to PBX enables to establish call between person near doorphone and PBX subscriber, as well as enter to protected area. It is also possible to trigger an electrolock, for opening door or gate, from phone connected to PBX.<br><br />
Additionally, DPH.IP doorphone can be used as fully functional access control system (ACS), due to registered events, that are send and visible in detailed billing application, or application designed especially for individual client. Thanks to installed, doorphone can control two relays (e.g. gate or doors), detect door opening or additional button pressing.<br><br />
Slican offers three types or DPH.IP-KSxxRF.C devices:<br />
<br><br><br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>DEVICE MODEL</b></center> !!{{Hl1}}|<center><b>FEATURES</b></center><br />
|-<br />
| <center><b>DPH.IP-CR0RF</b></center> ||<br />
* powered with Splitter UCS-CR<br />
* RFID card/pendant reader<br />
* one relay (EZ)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE (just ass ACS, without relay actions)<br />
* without calling feature<br />
<br />
|-<br />
| <center><b>DPH.IP-KS1RF.C</b></center> ||<br />
* doorphone with one call key<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
<br />
|-<br />
| <center><b>DPH.IP-KS4DRF.C</b></center> ||<br />
* doorphone with four keys (two navigational, one answering and one dismissing a call)<br />
* LCD display for showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
<br />
|-<br />
| <center><b>DPH.IP-KS16DRF.C</b></center> ||<br />
* doorphone with full alphanumeric keyboard<br />
* LCD display for configuring the device and showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
|}<br />
<br />
<br />
Following functions are available in DPH.IP doorphone (varies, depending on DPH model):<br />
* establish phone call using touch buttons arranged in form of numeric keyboard<br />
* two relays trigger:<br />
** electrolock (EZ)<br />
** additional relay (STA)<br />
* power supply with 12-25V AC lub 14-35V DC or PoE<br />
* Voltage thresholds for POD<br />
** <1.2V - Closed (0.65V)<br />
** 1.2V-2.4V - Open (1.8V)<br />
** >2.4V - Alarm (3.5V)<br />
* environment temperature range -20 to +70 (below 0 degrees, display reating time increases up to 10 seconds)<br />
* inputs COD (opening door sensori) i POD (opening door button). Both buttons operate with electrolock.<br />
* EZ trigger (opening) by receiving '''„1”''' or '''„*”''' character in DTMF code<br />
* built-in RFID card reader (Unique 125kHz standard, in accordance with EM4102)<br />
* possibility to trigger EZ or STA by registered RFID card approach<br />
* STA trigger (second relay) by receiving '''"2"''' character in DTMF code. Single pulse with fixed duration time is generated<br />
* graphical LCD display (except DPH.IP-KS1RF.C)<br />
<br />
=Maximum devices used depending on PBX type=<br />
{{Warning|DPH.IP, Audio.IP and CTS.IP resources in PBXes are shared.}}<br />
<br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>PBX TYPE</b></center> !!{{Hl1}}|<center><b>DPH.IP</b></center><br />
|-<br />
| <center>IPL-256</center>||<center>99</center><br />
|-<br />
| <center>IPM-032</center> ||<center>99</center><br />
|-<br />
| <center>IPM-032.LowCost</center> ||<center>10</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>28</center><br />
|-<br />
| <center>IPU-14.102</center> ||<center>68</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.100,101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.104.105<br>(LowCost)</center> ||<center>8</center><br />
|-<br />
| <center>MAC-6400</center> ||<center>99</center><br />
|-<br />
| <center>CCT-1668</center> ||<center>60</center><br />
|}</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=Characteristic_of_Slican_DPH.IP_doorphone&diff=7482Characteristic of Slican DPH.IP doorphone2017-06-09T13:32:22Z<p>Grzegorzz: /* Maksymalna ilość zastosowanych urządzeń w zależności od modelu centrali */</p>
<hr />
<div>Slican DPH.IP doorphone series connected to PBX enables to establish call between person near doorphone and PBX subscriber, as well as enter to protected area. It is also possible to trigger an electrolock, for opening door or gate, from phone connected to PBX.<br><br />
Additionally, DPH.IP doorphone can be used as fully functional access control system (ACS), due to registered events, that are send and visible in detailed billing application, or application designed especially for individual client. Thanks to installed, doorphone can control two relays (e.g. gate or doors), detect door opening or additional button pressing.<br><br />
Slican offers three types or DPH.IP-KSxxRF.C devices:<br />
<br><br><br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>DEVICE MODEL</b></center> !!{{Hl1}}|<center><b>FEATURES</b></center><br />
|-<br />
| <center><b>DPH.IP-CR0RF</b></center> ||<br />
* powered with Splitter UCS-CR<br />
* RFID card/pendant reader<br />
* one relay (EZ)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE (just ass ACS, without relay actions)<br />
* without calling feature<br />
<br />
|-<br />
| <center><b>DPH.IP-KS1RF.C</b></center> ||<br />
* doorphone with one call key<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
<br />
|-<br />
| <center><b>DPH.IP-KS4DRF.C</b></center> ||<br />
* doorphone with four keys (two navigational, one answering and one dismissing a call)<br />
* LCD display for showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
<br />
|-<br />
| <center><b>DPH.IP-KS16DRF.C</b></center> ||<br />
* doorphone with full alphanumeric keyboard<br />
* LCD display for configuring the device and showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
|}<br />
<br />
<br />
Following functions are available in DPH.IP doorphone (varies, depending on DPH model):<br />
* establish phone call using touch buttons arranged in form of numeric keyboard<br />
* two relays trigger:<br />
** electrolock (EZ)<br />
** additional relay (STA)<br />
* power supply with 12-25V AC lub 14-35V DC or PoE<br />
* Voltage thresholds for POD<br />
** <1.2V - Closed (0.65V)<br />
** 1.2V-2.4V - Open (1.8V)<br />
** >2.4V - Alarm (3.5V)<br />
* environment temperature range -20 to +70 (below 0 degrees, display reating time increases up to 10 seconds)<br />
* inputs COD (opening door sensori) i POD (opening door button). Both buttons operate with electrolock.<br />
* EZ trigger (opening) by receiving '''„1”''' or '''„*”''' character in DTMF code<br />
* built-in RFID card reader (Unique 125kHz standard, in accordance with EM4102)<br />
* possibility to trigger EZ or STA by registered RFID card approach<br />
* STA trigger (second relay) by receiving '''"2"''' character in DTMF code. Single pulse with fixed duration time is generated<br />
* graphical LCD display (except DPH.IP-KS1RF.C)<br />
<br />
=Maksymalna ilość zastosowanych urządzeń w zależności od modelu centrali=<br />
{{Warning|Zasoby urządzeń DPH.IP oraz Audio.IP w centrali są współdzielone z zasobami telefonów CTS.IP.}}<br />
<br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>TYP CENTRALI</b></center> !!{{Hl1}}|<center><b>ILOŚĆ<br>DPH.IP</b></center><br />
|-<br />
| <center>IPL-256</center>||<center>99</center><br />
|-<br />
| <center>IPM-032</center> ||<center>99</center><br />
|-<br />
| <center>IPM-032.LowCost</center> ||<center>10</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>28</center><br />
|-<br />
| <center>IPU-14.102</center> ||<center>68</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.100,101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.104.105<br>(LowCost)</center> ||<center>8</center><br />
|-<br />
| <center>MAC-6400</center> ||<center>99</center><br />
|-<br />
| <center>CCT-1668</center> ||<center>60</center><br />
|}</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=Characteristic_of_Slican_DPH.IP_doorphone&diff=7481Characteristic of Slican DPH.IP doorphone2017-06-09T13:31:55Z<p>Grzegorzz: /* Maximum doorphone quantity, depending on PBX type */</p>
<hr />
<div>Slican DPH.IP doorphone series connected to PBX enables to establish call between person near doorphone and PBX subscriber, as well as enter to protected area. It is also possible to trigger an electrolock, for opening door or gate, from phone connected to PBX.<br><br />
Additionally, DPH.IP doorphone can be used as fully functional access control system (ACS), due to registered events, that are send and visible in detailed billing application, or application designed especially for individual client. Thanks to installed, doorphone can control two relays (e.g. gate or doors), detect door opening or additional button pressing.<br><br />
Slican offers three types or DPH.IP-KSxxRF.C devices:<br />
<br><br><br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>DEVICE MODEL</b></center> !!{{Hl1}}|<center><b>FEATURES</b></center><br />
|-<br />
| <center><b>DPH.IP-CR0RF</b></center> ||<br />
* powered with Splitter UCS-CR<br />
* RFID card/pendant reader<br />
* one relay (EZ)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE (just ass ACS, without relay actions)<br />
* without calling feature<br />
<br />
|-<br />
| <center><b>DPH.IP-KS1RF.C</b></center> ||<br />
* doorphone with one call key<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
<br />
|-<br />
| <center><b>DPH.IP-KS4DRF.C</b></center> ||<br />
* doorphone with four keys (two navigational, one answering and one dismissing a call)<br />
* LCD display for showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
<br />
|-<br />
| <center><b>DPH.IP-KS16DRF.C</b></center> ||<br />
* doorphone with full alphanumeric keyboard<br />
* LCD display for configuring the device and showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
|}<br />
<br />
<br />
Following functions are available in DPH.IP doorphone (varies, depending on DPH model):<br />
* establish phone call using touch buttons arranged in form of numeric keyboard<br />
* two relays trigger:<br />
** electrolock (EZ)<br />
** additional relay (STA)<br />
* power supply with 12-25V AC lub 14-35V DC or PoE<br />
* Voltage thresholds for POD<br />
** <1.2V - Closed (0.65V)<br />
** 1.2V-2.4V - Open (1.8V)<br />
** >2.4V - Alarm (3.5V)<br />
* environment temperature range -20 to +70 (below 0 degrees, display reating time increases up to 10 seconds)<br />
* inputs COD (opening door sensori) i POD (opening door button). Both buttons operate with electrolock.<br />
* EZ trigger (opening) by receiving '''„1”''' or '''„*”''' character in DTMF code<br />
* built-in RFID card reader (Unique 125kHz standard, in accordance with EM4102)<br />
* possibility to trigger EZ or STA by registered RFID card approach<br />
* STA trigger (second relay) by receiving '''"2"''' character in DTMF code. Single pulse with fixed duration time is generated<br />
* graphical LCD display (except DPH.IP-KS1RF.C)<br />
<br />
=Maksymalna ilość zastosowanych urządzeń w zależności od modelu centrali=<br />
{{Uwaga|Zasoby urządzeń DPH.IP oraz Audio.IP w centrali są współdzielone z zasobami telefonów CTS.IP.}}<br />
<br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>TYP CENTRALI</b></center> !!{{Hl1}}|<center><b>ILOŚĆ<br>DPH.IP</b></center><br />
|-<br />
| <center>IPL-256</center>||<center>99</center><br />
|-<br />
| <center>IPM-032</center> ||<center>99</center><br />
|-<br />
| <center>IPM-032.LowCost</center> ||<center>10</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>28</center><br />
|-<br />
| <center>IPU-14.102</center> ||<center>68</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.100,101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.104.105<br>(LowCost)</center> ||<center>8</center><br />
|-<br />
| <center>MAC-6400</center> ||<center>99</center><br />
|-<br />
| <center>CCT-1668</center> ||<center>60</center><br />
|}</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=Characteristic_of_Slican_DPH.IP_doorphone&diff=7480Characteristic of Slican DPH.IP doorphone2017-06-09T13:29:26Z<p>Grzegorzz: /* Maximum doorphone quantity, depending on PBX type */</p>
<hr />
<div>Slican DPH.IP doorphone series connected to PBX enables to establish call between person near doorphone and PBX subscriber, as well as enter to protected area. It is also possible to trigger an electrolock, for opening door or gate, from phone connected to PBX.<br><br />
Additionally, DPH.IP doorphone can be used as fully functional access control system (ACS), due to registered events, that are send and visible in detailed billing application, or application designed especially for individual client. Thanks to installed, doorphone can control two relays (e.g. gate or doors), detect door opening or additional button pressing.<br><br />
Slican offers three types or DPH.IP-KSxxRF.C devices:<br />
<br><br><br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>DEVICE MODEL</b></center> !!{{Hl1}}|<center><b>FEATURES</b></center><br />
|-<br />
| <center><b>DPH.IP-CR0RF</b></center> ||<br />
* powered with Splitter UCS-CR<br />
* RFID card/pendant reader<br />
* one relay (EZ)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE (just ass ACS, without relay actions)<br />
* without calling feature<br />
<br />
|-<br />
| <center><b>DPH.IP-KS1RF.C</b></center> ||<br />
* doorphone with one call key<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
<br />
|-<br />
| <center><b>DPH.IP-KS4DRF.C</b></center> ||<br />
* doorphone with four keys (two navigational, one answering and one dismissing a call)<br />
* LCD display for showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
<br />
|-<br />
| <center><b>DPH.IP-KS16DRF.C</b></center> ||<br />
* doorphone with full alphanumeric keyboard<br />
* LCD display for configuring the device and showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
|}<br />
<br />
<br />
Following functions are available in DPH.IP doorphone (varies, depending on DPH model):<br />
* establish phone call using touch buttons arranged in form of numeric keyboard<br />
* two relays trigger:<br />
** electrolock (EZ)<br />
** additional relay (STA)<br />
* power supply with 12-25V AC lub 14-35V DC or PoE<br />
* Voltage thresholds for POD<br />
** <1.2V - Closed (0.65V)<br />
** 1.2V-2.4V - Open (1.8V)<br />
** >2.4V - Alarm (3.5V)<br />
* environment temperature range -20 to +70 (below 0 degrees, display reating time increases up to 10 seconds)<br />
* inputs COD (opening door sensori) i POD (opening door button). Both buttons operate with electrolock.<br />
* EZ trigger (opening) by receiving '''„1”''' or '''„*”''' character in DTMF code<br />
* built-in RFID card reader (Unique 125kHz standard, in accordance with EM4102)<br />
* possibility to trigger EZ or STA by registered RFID card approach<br />
* STA trigger (second relay) by receiving '''"2"''' character in DTMF code. Single pulse with fixed duration time is generated<br />
* graphical LCD display (except DPH.IP-KS1RF.C)<br />
<br />
=Maximum doorphone quantity, depending on PBX type=<br />
{{Warning|PBX resources for DPH.IP, Audio.IP and CTS.IP system phone are shared.}}<br />
<br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>PBX TYPE</b></center> !!{{Hl1}}|<center><b>DPH.IP<br>QUANTITY</b></center><br />
|-<br />
| <center>IPL-256</center>||<center>99</center><br />
|-<br />
| <center>IPM-032</center> ||<center>99</center><br />
|-<br />
| <center>IPM-032.LowCost</center> ||<center>10</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>28</center><br />
|-<br />
| <center>IPU-14.102</center> ||<center>68</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.100,101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.104.105<br>(LowCost)</center> ||<center>8</center><br />
|-<br />
| <center>MAC-6400</center> ||<center>99</center><br />
|-<br />
| <center>CCT-1668</center> ||<center>60</center><br />
|}</div>Grzegorzzhttp://pubwiki.slican.com/index.php?title=Characteristic_of_Slican_DPH.IP_doorphone&diff=7479Characteristic of Slican DPH.IP doorphone2017-06-09T13:21:46Z<p>Grzegorzz: </p>
<hr />
<div>Slican DPH.IP doorphone series connected to PBX enables to establish call between person near doorphone and PBX subscriber, as well as enter to protected area. It is also possible to trigger an electrolock, for opening door or gate, from phone connected to PBX.<br><br />
Additionally, DPH.IP doorphone can be used as fully functional access control system (ACS), due to registered events, that are send and visible in detailed billing application, or application designed especially for individual client. Thanks to installed, doorphone can control two relays (e.g. gate or doors), detect door opening or additional button pressing.<br><br />
Slican offers three types or DPH.IP-KSxxRF.C devices:<br />
<br><br><br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>DEVICE MODEL</b></center> !!{{Hl1}}|<center><b>FEATURES</b></center><br />
|-<br />
| <center><b>DPH.IP-CR0RF</b></center> ||<br />
* powered with Splitter UCS-CR<br />
* RFID card/pendant reader<br />
* one relay (EZ)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE (just ass ACS, without relay actions)<br />
* without calling feature<br />
<br />
|-<br />
| <center><b>DPH.IP-KS1RF.C</b></center> ||<br />
* doorphone with one call key<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
<br />
|-<br />
| <center><b>DPH.IP-KS4DRF.C</b></center> ||<br />
* doorphone with four keys (two navigational, one answering and one dismissing a call)<br />
* LCD display for showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
<br />
|-<br />
| <center><b>DPH.IP-KS16DRF.C</b></center> ||<br />
* doorphone with full alphanumeric keyboard<br />
* LCD display for configuring the device and showing data entered on keyboard<br />
* RFID card/pendant reader<br />
* two relays (EZ, STA)<br />
* door opened sensor and button (COD, POD)<br />
* powered with PoE<br />
|}<br />
<br />
<br />
Following functions are available in DPH.IP doorphone (varies, depending on DPH model):<br />
* establish phone call using touch buttons arranged in form of numeric keyboard<br />
* two relays trigger:<br />
** electrolock (EZ)<br />
** additional relay (STA)<br />
* power supply with 12-25V AC lub 14-35V DC or PoE<br />
* Voltage thresholds for POD<br />
** <1.2V - Closed (0.65V)<br />
** 1.2V-2.4V - Open (1.8V)<br />
** >2.4V - Alarm (3.5V)<br />
* environment temperature range -20 to +70 (below 0 degrees, display reating time increases up to 10 seconds)<br />
* inputs COD (opening door sensori) i POD (opening door button). Both buttons operate with electrolock.<br />
* EZ trigger (opening) by receiving '''„1”''' or '''„*”''' character in DTMF code<br />
* built-in RFID card reader (Unique 125kHz standard, in accordance with EM4102)<br />
* possibility to trigger EZ or STA by registered RFID card approach<br />
* STA trigger (second relay) by receiving '''"2"''' character in DTMF code. Single pulse with fixed duration time is generated<br />
* graphical LCD display (except DPH.IP-KS1RF.C)<br />
<br />
=Maximum doorphone quantity, depending on PBX type=<br />
{{Warning|PBX resources for DPH.IP doorphone and CTS.IP system phone are shared.}}<br />
<br />
{|{{Prettytable}}<br />
|-<br />
!{{Hl1}}|<center><b>PBX TYPE</b></center> !!{{Hl1}}|<center><b>DPH.IP<br>QUANTITY</b></center><br />
|-<br />
| <center>IPL-256</center>||<center>99</center><br />
|-<br />
| <center>IPM-032</center> ||<center>99</center><br />
|-<br />
| <center>IPM-032.LowCost</center> ||<center>10</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>28</center><br />
|-<br />
| <center>IPU-14.102</center> ||<center>68</center><br />
|-<br />
| <center>IPU-14.101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.100,101</center> ||<center>16</center><br />
|-<br />
| <center>IPS-08.104.105<br>(LowCost)</center> ||<center>8</center><br />
|-<br />
| <center>MAC-6400</center> ||<center>99</center><br />
|-<br />
| <center>CCT-1668</center> ||<center>60</center><br />
|}</div>Grzegorzz