DPH - Opening doorphone casing - Revision history

Leszekj at 13:32, 1 June 2020

2020-06-01T13:32:14Z

2011-10-19T07:39:21Z

2011-09-01T12:21:00Z

2011-09-01T12:16:54Z

2011-08-31T13:23:48Z

2011-08-31T13:23:02Z

2011-08-31T13:00:37Z

2011-08-31T12:59:26Z

2011-08-31T12:58:58Z

2011-08-31T12:32:49Z

@@ Line 1: / Line 1: @@
 Front panel of DPH doorphone is fixed by wrench srews M4, included in purchased set. Location of these screws is marked by digit 1, visible on below figures.
-<center>[[File:DPH KS1RF przod oznaczenia.png]][[File:DPH KS2RF przod oznaczenia.png]]</center>
+<center>[[File:DPH.AB-KS1RF.DG_oznaczenia.png]][[File:DPH.AB-KS2RF.C_oznaczenia.DG.png]]</center>
 Following table explains marking used on figures.
 {|{{prettytable}}
@@ Line 9: / Line 9: @@
 |2||Doorphone speaker cover
 |-
-|3||Hole for microphone installed in doorphone
+|3||Blind hole
 |-
-|4||Address window
+|4||Blind holes
 |-
-|5||Establish call button
+|5||Address window
 |-
-|6||Mark, informing about RFID card reader
+|6||Establish call button
 |-
 |}
-{{warning|If in doorphones, which include embedded RFID card reader, you use card with standard credit card dimensions, it is enough to approach this card to 5 - 6cm from doorphone, in parallel to doorphone, bellow speaker so over PCB presented on below figure. If you use small pendants as RFID card, it is recommended to aproach such pendant to 1cm in place where there is mark described as 6 on above figures.}}
 To front panel the PCB board is fixed. It is visible after removing front panel. All elements neccessarily to doorphone installation are accessible and it is not needed to remove PCB from front panel. View of PCB fixed to front panel is presented on following figure:
 <center>[[File:DPH KS1(2) wnetrze.png]]</center>

@@ Line 1: / Line 1: @@
-Front panel of DPH doorphone is fixed by wrench srews M4, included in prchased set. Location of these screws is marked by digit 1, visible on below figures.
+Front panel of DPH doorphone is fixed by wrench srews M4, included in purchased set. Location of these screws is marked by digit 1, visible on below figures.
 <center>[[File:DPH KS1RF przod oznaczenia.png]][[File:DPH KS2RF przod oznaczenia.png]]</center>
 Following table explains marking used on figures.

@@ Line 19: / Line 19: @@
 |}
 {{warning|If in doorphones, which include embedded RFID card reader, you use card with standard credit card dimensions, it is enough to approach this card to 5 - 6cm from doorphone, in parallel to doorphone, bellow speaker so over PCB presented on below figure. If you use small pendants as RFID card, it is recommended to aproach such pendant to 1cm in place where there is mark described as 6 on above figures.}}
-To front panel the PCB board is fixed. Widoczna jest ona po zdjęciu panelu przedniego. Wszelkie elementy niezbędne do instalacji bramofonu są widoczne, dostępne i nie jest konieczne odkręcanie płytki elektroniki od panelu przedniego. Widok płytki elektroniki przykręconej do panelu przedniego prezentuje poniższy rysunek:
+To front panel the PCB board is fixed. It is visible after removing front panel. All elements neccessarily to doorphone installation are accessible and it is not needed to remove PCB from front panel. View of PCB fixed to front panel is presented on following figure:
 <center>[[File:DPH KS1(2) wnetrze.png]]</center>

@@ Line 19: / Line 19: @@
 |}
 {{warning|If in doorphones, which include embedded RFID card reader, you use card with standard credit card dimensions, it is enough to approach this card to 5 - 6cm from doorphone, in parallel to doorphone, bellow speaker so over PCB presented on below figure. If you use small pendants as RFID card, it is recommended to aproach such pendant to 1cm in place where there is mark described as 6 on above figures.}}
-Do panelu przedniego przykręcona jest płytka z elementami elektronicznymi. Widoczna jest ona po zdjęciu panelu przedniego. Wszelkie elementy niezbędne do instalacji bramofonu są widoczne, dostępne i nie jest konieczne odkręcanie płytki elektroniki od panelu przedniego. Widok płytki elektroniki przykręconej do panelu przedniego prezentuje poniższy rysunek:
+To front panel the PCB board is fixed. Widoczna jest ona po zdjęciu panelu przedniego. Wszelkie elementy niezbędne do instalacji bramofonu są widoczne, dostępne i nie jest konieczne odkręcanie płytki elektroniki od panelu przedniego. Widok płytki elektroniki przykręconej do panelu przedniego prezentuje poniższy rysunek:
 <center>[[File:DPH KS1(2) wnetrze.png]]</center>

@@ Line 18: / Line 18: @@
 |-
 |}
-{{warning|If in doorphones, which include embedded RFID card reader, you use card with standard credit card dimensions, it is enough to approach this card to 5 - 6cm from doorphone, in parallel to doorphone, bellow speaker so over PCB presented on below figure. If you use small pendants as RFID card, it is recommended to aproach such pendant to 1cm in place where there is sign described as 6 on above figures.}}
+{{warning|If in doorphones, which include embedded RFID card reader, you use card with standard credit card dimensions, it is enough to approach this card to 5 - 6cm from doorphone, in parallel to doorphone, bellow speaker so over PCB presented on below figure. If you use small pendants as RFID card, it is recommended to aproach such pendant to 1cm in place where there is mark described as 6 on above figures.}}
 Do panelu przedniego przykręcona jest płytka z elementami elektronicznymi. Widoczna jest ona po zdjęciu panelu przedniego. Wszelkie elementy niezbędne do instalacji bramofonu są widoczne, dostępne i nie jest konieczne odkręcanie płytki elektroniki od panelu przedniego. Widok płytki elektroniki przykręconej do panelu przedniego prezentuje poniższy rysunek:
 <center>[[File:DPH KS1(2) wnetrze.png]]</center>