SKD Instruction manual v1.03 - Revision history

Grzegorzg: /* Previous version */

2011-03-14T09:14:20Z

‎Previous version

Grzegorzg: /* Previous version */

2011-03-14T09:13:59Z

‎Previous version

Grzegorzg: /* Notes */

2011-03-14T09:13:40Z

‎Notes

Grzegorzg: /* Programming options */

2011-03-11T08:45:50Z

‎Programming options

Grzegorzg: /* Programming options */

2011-03-11T08:44:47Z

‎Programming options

Grzegorzg: /* Programming options */

2011-03-11T08:43:26Z

‎Programming options

Grzegorzg: /* Description of terminals */

2011-03-11T08:41:45Z

‎Description of terminals

Grzegorzg: /* Description of terminals */

2011-03-11T08:40:23Z

‎Description of terminals

Grzegorzg: /* Notatki */

2011-03-11T08:36:22Z

‎Notatki

Grzegorzg: Created page with "=SKD= '''Doorphones''' '''SKD.RF''' Installation and operational instruction File:IO_SKD_casing_has.jpg‎ [[..."

2011-03-07T10:04:58Z

Created page with "=SKD= <center>'''Doorphones'''</center> <center>'''SKD.RF'''</center> <center>Installation and operational instruction</center> <center>File:IO_SKD_casing_has.jpg‎ [[..."

Show changes

@@ Line 677: / Line 677: @@
 = Previous version =
-Previous version of this instruction manual can be found [[SKD Instruction manual v1.01|here]].
+Previous version of this Instruction manual can be found [[SKD Instruction manual v1.01|here]].
 = Notes =

@@ Line 678: / Line 678: @@
 = Previous version =
 Previous version of this instruction manual can be found [[SKD Instruction manual v1.01|here]].
 = Notes =

← Older revision		Revision as of 09:13, 14 March 2011
Line 676:		Line 676:
	<center>[[Image:io skd proper equipement.png]]</center>		<center>[[Image:io skd proper equipement.png]]</center>

		+	= Previous version =
		+	Previous version of this instruction manual can be found [[SKD Instruction manual v1.01\|here]].
	= Notes =		= Notes =

@@ Line 449: / Line 449: @@
 Pressing '''0''' key causes only short-cirquit – calls in PABX should be routed appropriately via „hot line”.
 |-
-!{{Hl3}} colspan="2" |'''Forwarding <ref name="ftn10">'''Used if doorphone is connected to the PABX.'''</ref>
+!{{Hl3}} colspan="2" |'''Forwarding '''<ref name="ftn10">Used if doorphone is connected to the PABX.</ref>
 |-
 |'''P21'''|| '''<nowiki>[1] = Extension number assigned to button 1.</nowiki>'''

@@ Line 441: / Line 441: @@
 Adjustement range = ''1..30''
 |-
-|'''P14'''||'''<nowiki>[no]</nowiki><ref name="ftn9">'''Two options are available – no and yes '''</ref> = Hot line after entering "0" digit.'''
+|'''P14'''||'''<nowiki>[no]</nowiki>'''<ref name="ftn9">Two options are available – no and yes </ref> = Hot line after entering "0" digit.
 Value change:

@@ Line 423: / Line 423: @@
 This field has information meaning and depends on jumper location on CONFIG terminal (allowed value are from ''0..15''). Every cassette number must be unique if there are few doorphones in the system.
 |-
-|'''P12'''||'''<nowiki>[4321]</nowiki><ref name="ftn8">'''<nowiki>In brackets [ ] default values are shown.</nowiki>'''</ref> = Access code (PIN) – '''is used to opening door electro-lock.
+|'''P12'''||'''<nowiki>[4321]</nowiki>'''<ref name="ftn8"><nowiki>In brackets [ ] default values are shown.</nowiki></ref> = Access code (PIN) – is used to opening door electro-lock.
 Value change:

@@ Line 211: / Line 211: @@
 |colspan="2"|{{warning|Device can be powered only from one of mentioned above sources.}}
 |-
-|'''C / NO<ref name="ftn5">'''NO (''Normally Open''), NC (''Normally Closed'')'''; maximal load capacity of NO and NC is equal to 24V, 2A</ref> (NC)'''|| Terminals for relay output used to controll electro-lock. They should be connected in series in electro-lock supply circuit. Due to using NO terminal (terminals stay closed for a programmed time) or NC (terminals stay open for a programmed time) it is possible to connect any device controlling opening door.
+|'''C / NO<ref name="ftn5">'''NO''' (''Normally Open''), '''NC''' (''Normally Closed''); maximal load capacity of NO and NC is equal to 24V, 2A</ref> (NC)'''|| Terminals for relay output used to controll electro-lock. They should be connected in series in electro-lock supply circuit. Due to using NO terminal (terminals stay closed for a programmed time) or NC (terminals stay open for a programmed time) it is possible to connect any device controlling opening door.
 |-
 | '''POD /GND'''|| To these terminals button or movement sensor can be connected, which are used to opening door from inside. Closing these terminals (pressing button) causes relay switching on, for a time of pressing button plus time defined during doorphone programming, this time starts running after releasing button. Such button (movement sensor) operate independently on doorphone status (call, standby mode).

@@ Line 676: / Line 676: @@
 <center>[[Image:io skd proper equipement.png]]</center>
-= Notatki =
+= Notes =
 ----
 <references/>