Difference between revisions of "ITS - Outgoing calls"
From pubWiki-en
(→Examples of configuration using Outgoing calls scenario) |
(→Examples of configuration using Outgoing calls scenario) |
||
| Line 61: | Line 61: | ||
* '''Outgoing rule 1''' should be assigned to ports for '''audio''' calls | * '''Outgoing rule 1''' should be assigned to ports for '''audio''' calls | ||
* '''Outgoing rule 2''' should be assigned to ports for data transmission - these ports should use '''only''' POTS Lines (FXO) | * '''Outgoing rule 2''' should be assigned to ports for data transmission - these ports should use '''only''' POTS Lines (FXO) | ||
| − | ||''' | + | ||'''Outgoing rule 1'''<br>[[File:LCR - IPO - FXO.png]]<br>'''Outgoing rule 2'''<br>[[File:ITS LCR FXO.png]] |
|- | |- | ||
|4.||'''Dom dwurodzinny''' Rodzice+Dzieci. | |4.||'''Dom dwurodzinny''' Rodzice+Dzieci. | ||
Porty należy podzielić na 2 grupy: | Porty należy podzielić na 2 grupy: | ||
| − | * porty Rodziców - porty przypisać do ''' | + | * porty Rodziców - porty przypisać do '''Outgoing rule 1''' - mają korzystać w pierwszej kolejności ze swojej linii VoIP w drugiej z linii POTS. |
| − | * porty Dzieci - muszą korzystać '''wyłącznie''' ze swojej Linii IP (IPO) - porty przypisać do ''' | + | * porty Dzieci - muszą korzystać '''wyłącznie''' ze swojej Linii IP (IPO) - porty przypisać do '''Outgoing rule 2''' |
* Połączenia alarmowe powinny być zawsze realizowane przez linię POTS, niezależnie czy numer wybierają dzieci czy rodzice. | * Połączenia alarmowe powinny być zawsze realizowane przez linię POTS, niezależnie czy numer wybierają dzieci czy rodzice. | ||
| − | ||''' | + | ||'''Outgoing rule 1'''<br>[[File:LCR Rodzice.png]]<br>'''Outgoing rule 2'''<br>[[File:LCR Dzieci.png]] |
|} | |} | ||
---- | ---- | ||
[[Slican_ITS |Back]] | [[Slican_ITS |Back]] | ||
[[Category:ITS]] | [[Category:ITS]] | ||
Revision as of 09:50, 13 August 2010
Contents
Outgoing methods
ITS offers 3 methods of realizing outgoing calls:
- Outgoing via 0
- Generic - automatic outgoing,
- Manual selection of specified outgoing line(FXO or IPO)
|
Outgoing via zero
Starting from firmware version 1.01.1080 global option, which interprets as outgoing all numbers with zero, was added. Settings this option is available in pane Global options: Reaching public newtork by 0. Further steps should be the same as for option: Generic - automatic outgoing.
Generic - automatic outgoing
|
| Pane Subscribers (FXS) or IP Subscribers (IPS) section Additional options For every subscriber one of following outgoing option should be set: Outgoing ruleFor specified subscriber one of following outgoing rules can be assigned: Outgoing rule 1 or Outgoing rule 2, Fixed assignment of specified outgoing line FXO or IPOIt means, that specified subscriber, independently on dialed number will be routed via assigned in configuration outgoing line. |
 Selection of outgoing calls scenario. By default: Outgoing rule 1 |
Outgoing rule - number dialing scenario
| For specified subscribers one of two outgoing scenario can be set: Outgoing rule 1 or Outgoing rule 2 Configuration of scenario: Outgoing rule:
|
 Scenario tables: Outgoing rule 1/2 |
Options All FXO's/All IPO's
- Seizing lines for option All FXO's: Line 41->Line 42->Line 41 etc....seized cyclically. It can be also used if only one line is connected.
- Seizing lines for option All IPO's: IPLine 51->IPLine 52->IPLine 53->IPLine 54->IPLine 55->IPLine 56->IPLine 51 etc....so next after lastly occupied.
Examples of configuration using Outgoing calls scenario
| No | Requirements/ Assumptions | How to do it? Outgoing rule pane view |
|---|---|---|
| 1. | All outgoing calls are routed via outgoing lines in following order:
|
|
| 2. | All outgoing calls are routed as in example 1 except following calls:
|
|
| 3. | Office at home - office equipped with fax and modem.
Ports should be divided into two groups:
|
Outgoing rule 1 Outgoing rule 2 
|
| 4. | Dom dwurodzinny Rodzice+Dzieci.
Porty należy podzielić na 2 grupy:
|
Outgoing rule 1 Outgoing rule 2 
|
