Difference between revisions of "MSB-1102 Instruction manual"
From pubWiki-en
(→Certificate of conformity, proper equipement disposal) |
|||
| (14 intermediate revisions by the same user not shown) | |||
| Line 4: | Line 4: | ||
<center><big>'''Instruction manual v.1.00'''</big></center> | <center><big>'''Instruction manual v.1.00'''</big></center> | ||
=Information= | =Information= | ||
| − | '''Slican Multi Switch Box MSB-1102''' | + | '''Slican Multi Switch Box MSB-1102''' it is device assuring cooperation between Slican PABX<ref name="centrale_i_firmware">'''MSB-1102''' can be used with firmware version 4.10 or later. It can be used with Slican PABXes: CXS-0424, CCT-1668, MAC-Zero, MAC-6400.</ref> and sensors, relays, alarm systems, paging systems etc.<br> |
| − | + | Subscriber port in PABX should be configured as '''Sensor''' or '''Relay''' – depending on required function.<br> | |
| − | [[MSB- | + | [[MSB-1102 Instruction manual#Parameters |Power supply parameters.]] |
=MSB-1102 Structure= | =MSB-1102 Structure= | ||
| − | MSB-1102 | + | MSB-1102 is equipped with following input/output ports: |
| − | * | + | *sockets AB1/AB2 type RJ11 for connecting 2 subscriber ports in PABX, |
| − | * | + | *socket 2REL<ref name="funkcje">Device uses 2 independent channels. It means that simultaneously two functions can operate. Ex: 2 sensors, 2 relays or mix.</ref> (REL1/REL2) type RJ45 which includes: |
| − | ** | + | **sensor terminals (SNS1/SNS2) – configurable, |
| − | ** | + | **monostable relay terminals<ref name="czas_impulsu>Release pulse time is about 1 second.</ref> – configurable, |
| − | * | + | *socket ZAS – local power supply from external source. |
=Connecting and preparing for configuration= | =Connecting and preparing for configuration= | ||
==Configuration Jumpers== | ==Configuration Jumpers== | ||
{| | {| | ||
| − | |[[ | + | |[[File:MSB jumpers small.png]]|| |
{|{{prettytable}} | {|{{prettytable}} | ||
| − | |X1-X3 - | + | |X1-X3 - Sensor 1 operating mode (SNS1)||X4-X6 - Sensor 2 operating mode (SNS2) |
|- | |- | ||
| − | |X10-X12 – | + | |X10-X12 – Relay 1 operating mode (REL1)||X7-X9 - Relay 2 operating mode (REL2) |
|- | |- | ||
|} | |} | ||
| Line 33: | Line 33: | ||
=Operating modes= | =Operating modes= | ||
{|{{prettytable}} | {|{{prettytable}} | ||
| − | !{{Hl3}}| | + | !{{Hl3}}|Power supply!! {{Hl3}}|Sensors (SNS)!!{{Hl3}}|Relays (REL) |
|- | |- | ||
| − | | | + | |Without power supply||[[File:MSB DCI mode.png]]<br>||[[File:MSB REL NO NC small.png]] |
|- | |- | ||
| − | | | + | |With power supply||[[File:MSB CCS mode.png]]||[[File:MSB VON VOFF small.png]] |
|- | |- | ||
|} | |} | ||
| − | + | According above table '''MSB-1102''' must be supplied from local power supply device in following operating modes: | |
| − | * | + | * Sensors: CCS mode |
| − | * | + | * Relays: VON/VOFF mode |
=Parameters= | =Parameters= | ||
| − | * | + | * current downloaded from power supply unit in CCS mode - max. 20mA. |
| − | * | + | * current downloaded in DCI mode - max.10mA per sensor. |
| − | * | + | * relay terminal parameters (for NO/NC and VON/VOFF modes) - max 42VAC/0.5A, 42VDC/1A |
| − | * | + | * Sensor activate voltage range - DCI and CCS modes - 5-30V<ref name="polaryzacja">Attention: Polarity is important</ref>DC. |
<br> | <br> | ||
| − | {{warning| | + | {{warning|It is not allowed to direct controlling with 230VAC voltage. For this purpose, appropriate external relays, connected to 2REL socket should be used.}} |
| − | =[[MSB | + | =[[MSB Certificate of conformity |Certificate of conformity, proper equipement disposal]]= |
---- | ---- | ||
{{References}} | {{References}} | ||
Latest revision as of 10:53, 10 January 2011
Contents
Information
Slican Multi Switch Box MSB-1102 it is device assuring cooperation between Slican PABX[1] and sensors, relays, alarm systems, paging systems etc.
Subscriber port in PABX should be configured as Sensor or Relay – depending on required function.
MSB-1102 Structure
MSB-1102 is equipped with following input/output ports:
- sockets AB1/AB2 type RJ11 for connecting 2 subscriber ports in PABX,
- socket 2REL[2] (REL1/REL2) type RJ45 which includes:
- sensor terminals (SNS1/SNS2) – configurable,
- monostable relay terminals[3] – configurable,
- socket ZAS – local power supply from external source.
Connecting and preparing for configuration
Configuration Jumpers
 |
|
Operating modes
| Power supply | Sensors (SNS) | Relays (REL) |
|---|---|---|
| Without power supply |  |
|
| With power supply |  |
|
According above table MSB-1102 must be supplied from local power supply device in following operating modes:
- Sensors: CCS mode
- Relays: VON/VOFF mode
Parameters
- current downloaded from power supply unit in CCS mode - max. 20mA.
- current downloaded in DCI mode - max.10mA per sensor.
- relay terminal parameters (for NO/NC and VON/VOFF modes) - max 42VAC/0.5A, 42VDC/1A
- Sensor activate voltage range - DCI and CCS modes - 5-30V[4]DC.
|
Certificate of conformity, proper equipement disposal
References
- ↑ MSB-1102 can be used with firmware version 4.10 or later. It can be used with Slican PABXes: CXS-0424, CCT-1668, MAC-Zero, MAC-6400.
- ↑ Device uses 2 independent channels. It means that simultaneously two functions can operate. Ex: 2 sensors, 2 relays or mix.
- ↑ Release pulse time is about 1 second.
- ↑ Attention: Polarity is important
