Latest revision as of 11:53, 4 April 2011

Introduction

Dear user - thank You for purchasing Slican ITS system.

Slican ITS cooperate with:

• analogue telephone devices: phones, faxes, modems. These devices can be both: tone (DTMF) or pulse dialing
• analogue external lines (POTS)
• VoIP^[1] (SIP) devices or softphones
• VoIP (SIP) providers

System is perfectly suited for small companies, offices, single-family homes etc. Due to DISA^[2] function, it is possible to automatic establishing incoming calls using DTMF^[3] signal. VoIP functions make system flexible and easy in configuration.

Basic parameters and features of Slican ITS

Available models

Where:

• FXO - (Foreign eXchange Office) external analogue telefon line POTS^[4] port - to this port line from upper exchange is connected.
• FXS - (Foreign eXchange Station) internal ab phone port - to this port phone/fax/modem etc. is connected.
• IPO - IP line port - this port can be logged into VoIP provider or another VoIP PBX.
• IPS - IP subscriber port - to this port SIP client can be logged in (gateway, SIP phone, SoftPhone type application).

Functionality

• remote managing via LAN network or Internet, using web browser installed on PC
• ClipFSC presentation receiving on POTS lines
• number presentation on internal lines
• VoIP-SIP calls maintenance
• possibility of configuration of restriction in establishing outgoing calls depending on subscriber
• cooperation with Slican BRV and SKD doorphones
• different ringtones for internal and incoming calls
• 3 standard DISA announcements with possibility of changing them
• upringing subscriber group
• call transfer
• call forwarding
• call history

Technical data

• power supply ~230V, 50Hz
• power consumption: 3W in standby mode; max.: 11W – if all phones ringing
• internal and external ports protected against overvoltage from telecommunication network
• analogue ports suitable for phones with pulse or tone (DTMF) dialing
• FXS analogue port range - up to 1000m
• LAN port (Ethernet 10/100 with auto MDI/MDIX) for maintenance of VoIP connection and programming
• fulfiling requirement of R&TTE directive
• casing dimensions 191x111x36 [mm].

Package content

Slican ITS elements

ITS Terminals

LED Meaning

PBX restart continues about 30 seconds (if PBX is set as a DHCP client) or about 90 seconds (if fixed IP address is set in PBX).

Using phone functions of PBX

In this chapter services realized by analogue phones equipped in pulse (DTMF) dialing.

Attention: some functions are unavailable for VoIP devices.

Internal calls

Extension number should be dialed (see: 4.2.1 Phones/subscriber ports or 4.2.2 Extension number upringing groups) and dialing should be accepted by # (Hash).

Numbering - port numbers

Phones/subscriber ports

• 21..26 – numbers of internal phone ports (FXS)

• 31 – number of IP subscribers/VoIP phones/VoIP clients (concerns ITS-0106 and ITS-0206)

• 31..38 – numbers of IP subscribers/VoIP phones/VoIP clients (concerns ITS-0286)

Extension number upringing groups

• 61..63 – group numbers (accessible only from inside PBX, they cannot be dialed during DISA)

Lines/trunks/external ports

*41 – port for POTS line – FXO1 (concerns ITS-0106)

*41; *42 – ports for POTS lines – FXO1 and FXO2 (concerns ITS-0206 and ITS-0286)

*51..*52 – ports for VoIP lines – IPO (concerns ITS-0106 and ITS-0206)

*51..*56 – ports for VoIP lines – IPO (concerns ITS-0286)

Finishing number dialing #

Pressing # - finishes number dialing and accelerates dialing specified number by PBX.

External/outgoing calls

External number should be dialed and confirmed by #. PBX automatically (according programmed settings) routes call via specified outgoing line. By default it is FXO1 or FXO2. It is also possible to "manual" outgoing line selection (4.2.3 Lines/trunks/external ports).

Following settings types, concerned with external number dialing, are available:

Outgoing via zero

Starting from firmware version 1.01.1080 global option, which interprets as outgoing all numbers with zero, was added. Settings this option is available in pane Global options: Reaching public newtork by 0.

Outgoing calls using outgoing rules included in tables (Outgoing calls 1 and Outgoing calls 2).

For specified subscribed appropriate rule (Outgoing calls 1 or Outgoing calls 2) is assigned.

Fixed assignment of specified outgoing line (IPO or FXO).

It means, that specified subscriber, independently on dialed number will be routed via assigned in configuration outgoing line.

Manual selection of line for establishing outgoing call.

Before dialing external number, number of outgoing line should be selected (see: 4.2.3 Lines/trunks/external ports)

Transferring calls

To transfer current call, you should press Flash^[5] button and dial target number. Caller will hear a melody and call will be holded.
A If target number is free:

1. you hang up the handset and target number start ringing – if it is transfer without offering. If you can hear target phone ringing and nobody answer this call, you can intercept this ringing back by selecting service code *978.
2. you wait until somebody answer the call (to inform receiver about transferred call) – next you hang up the handset - it is transfer with offering. If nobody answer call on target phone, you can return to holded call by pressing 2 x flash.

B If target number is busy, you can:

1. press flash button once more – you return to holded call,
2. hang up the handset – holded call rings back.

Call forwarding *72 - on / *73 - off

• To activate call forwarding dial *72 target_number and press # - after service activation, you can hear confirmation Service is active.
• Code *73 should be selected to service deactivation.

Call intercerption *978

*978 - call interception (digits 78 ≡ PU PickUp) – if another connected to PBX phone is ringing you can „intrercept” this call by selecting this code.

Answering doorphone calls during another call

If any call is established and doorphone call is coming – subscriber hears short beep signal. In following situation it is possible:

• finish call and after hang up handset, doorphone start ringing.
• press flash button and dial extension number assigned to doorphone (phone call is holded); after next flash pressing subscriber returns to phone call.

Conference calls, 3PTY calls.

During call (outgoing, incoming, internal):

1. press flash button,
2. dial extension number of third person of conference, after establishing call:
3. press flash button and next 3 – conference call is established.

Conference call is disconnected if at least two conference participants disconnect himself/herself.

Quick start

Power supply should be connected to PBX – LED diodes located on casing start blinking

After finishing start procedure POWER LED will be shine continuously.

For any FXS port, phone required for configuration should be connected.

Inside LAN network with DHCP service

Check IP address: Lift handset and dial *947.

ITS generate voice message with IP address received from DHCP.

To switch on DHCP service (if previously this service was inactive) dial *931. ITS confirm by voice message: „Service is accepted”.

Inside LAN network without DHCP service

To switch off DHCP service: Lift handset and dial *930. ITS confirm by voice message: „Service is accepted” and perform restart with default network settings:

IP:192.168.0.247 MASK:255.255.255.0 GATEWAY:192.168.0.1 DNS:194.204.159.1

For this option listening address service *947 is active.

Configuration and compatible browsers

ITC can be configured using Internet browser.

To connect with PBX, in browser address bar should be entered ITS IP address received from this device (see: 5.1 Inside LAN network with DHCP service or 5.2 Inside LAN network without DHCP service) Default password: slican.

Compatible Internet browsers:

• FireFox 3.5.x and 3.0.x
• Google Chrome 3.x

Configuration window elements

Checking newest software version

First activity after connecting PBX should be checking current software (Firmware) installed in ITS (Pane: Update). More in chapter concerning firmware updating.

Resetting password

Press and hold for about 2 seconds button Reset. When all diodes start blinking current password is reset to default(slican).

Retrieve default settings

1. Disconnect power cable from 12V socket
2. Press (ex. using paper clip) and hold reset button (near power supply socket)
3. Connect power cable to 12V socket
4. Wait until all diodes shine and release reset button.

Such reset restore default PBX settings

VoIP function configuration - examples

Using VoIP provider

Every outgoing call can be realized via:

• FXO – analogue line connected to ITS
• IPO – configured VoIP service

Because services of VoIP provider are usually cheapper, it is possible to route all outgoing calls via such provider firstly and if establishing call via VoIP is impossible because of any reason (ex. lack of Internet) ITS routes call via FXO (POTS) lines. However while fax, modem or any other data transmission, it is necessarily to route such call directly via FXO line to PSTN network.

Outgoing order is set in panes Outgoing calls 1 and Outgoing calls 2, and depends on prefix.

IPO - VoIP line configuration

Pane: IP Lines (IPO):

To configure/assign specified provider following should be done:

1. Selection of VoIP line.
2. Fulfilling data concerned with specified VoIP account defined by provider.

Default port is equal to 5060, it can be changed for any line separately.

Outgoing method is defined in Panes: Outgoing calls 1 and Outgoing calls 2.

Using VoIP subscriber

Depending on Slican ITS model from 1 to 8 IPS (VoIP subscribers) can be logged.

According presented figure, VoIP subscriber can be can be any client in LAN network or outside of it - in Internet network.

VoIP subscribers extend PBX capacity and its range. Due to this feature company's extension numbers can exist everywhere, if Internet network is available, can use external ITS lines according assigned privileges.

IPS - IP subscriber configuration

Pane: IP Subscribers (IPS):

To configure IP subscriber account following should be done:

1. Subscriber should be selected from list.
2. Enable selected subscriber.
3. Password should be assigned to VoIP subscriber. Password can be entered manually or generated by pressing adjacent button.

Attension! Extension number is always used as login.

1. Additional parameters of IP subscriber are: codecs used by subscriber and subscriber comment.

If remote subscriber (outside LAN) login is required, port forwarding in router to ITS address in LAN. SIP port (signaling) for IP sunscribers: 5060 UDP by default (it can be changed in pane Global options). RTP ports: 8100-8200 UDP It is recommended to assign fixed address to PBX.

Admin service codes

• *981 - echo test – useful during PBX startup (only for internal calls)

• *982 - melody test – useful during PBX startup (only for internal calls)

• *947 – read PBX IP address (47 ≡ IP)

• *931 - switching on DHCP client in ITS (default settings)
• *930 - switching off DHCP client in ITS and assigning default IP parameters

Firmware updating

If ITS is connected to the Internet, it is recommended to upgrade ITS firmware (if newer version is available).

Pane Update->Find update->Select version->Update.

Attention! After firmware update execution all settings are removed, so before updating configuration printout should be done. It can be used in configuration restore after updating.

Safety requirements while using ITS

Security rules and proper using must be obligatory observed for assuring device proper operation.

Below basic rules concerning ITS are presented. Without fulfiling these rules any claim or notice presented by users cann't be accepted by manufacturer.

Rules presented here concerns installation, premises and requirements concerning power supply network.

Installation

• Device should be installed and startup by service with manufacturer authorization.
• All installation activities should be performed according assembly and safety rules.
• Due to heat abstraction it is recommended to install ITS in vertical position, so terminals should be accessible from the right side of device.

Work environment

1. Due to durability and operating quality of electronic elements device should not be installed inside buildings or spaces with high humidity.
2. Due to risk of flood of water, device should not be located near water reservoirs (pools, taps, etc.).
3. Device should not be installed in premises with high dustiness or electromagnetic field intensity.

It is not recommended to install ITS in following permises:

1. in premises with direct influence of solar light,
2. in premises where vibration are very often or strong,
3. near radio aerials.

All devices connected to ITS should have certificates of conformity with EU regulations.

Certificate of conformity, proper device disposal

CERTIFICATE OF CONFORMITY
Manufacturer: SLICAN sp. z o.o. ul. M. Konopnickiej 18 85-124 Bydgoszcz	Type: IP PBX	Models: SLICAN ITS-0106 SLICAN ITS-0206 SLICAN ITS-0286
Device description: IP PBX ITS-0206; ITS-0286 with capacity of 8 ports and ITS-0106 with capacity of 7 ports, plus VoIP. Up to 6 analogue phones with tone or pulse dialing and VoIP phones can be connected to the PBX. Device can cooperate with PSTN network using annalogue trunkss with ASS signaling and with VoIP providers using LAN interface.
Product fulfiles following EU Directive 99/5/WE R&TTE, it also fulfiles requirements of following harmonized standards: EN 60950-1:2007;EN 55022:1998 + A1:2000 + A2:2003;EN 55024:1998 + A1:2001 + A2:2003
Additional information: Current text of certificate of conformity can be downloaded from website www.slican.com ITS fulfiles requirements concerning allowed disturbances level for B class devices.
Bydgoszcz, 01-07-2010

1. ↑ ang. Voice over IP – transmitting voice in IP networks
2. ↑ ang. Direct Inward System Access – service enables to dial extension number without operator help.
3. ↑ ang. Dual Tone Multi Frequency – method of pulse digits dialing
4. ↑ ang. Plain Old Telephone Service – standard telephone line
5. ↑ Depending on phone type name Flash, R or Recall is used