Difference between revisions of "DPH - Opening doorphone casing"

From pubWiki-en
Jump to: navigation, search
 
(7 intermediate revisions by one other user not shown)
Line 1: Line 1:
−
Front panel of DPH doorphone is fixed by wrench srews M4, included in prchased set. Location of these screws is marked by digit 1, visible on below figures.
+
Front panel of DPH doorphone is fixed by wrench srews M4, included in purchased set. Location of these screws is marked by digit 1, visible on below figures.
−
<center>[[File:DPH KS1RF przod oznaczenia.png]][[File:DPH KS2RF przod oznaczenia.png]]</center>
+
<center>[[File:DPH.AB-KS1RF.DG_oznaczenia.png]][[File:DPH.AB-KS2RF.C_oznaczenia.DG.png]]</center>
 
Following table explains marking used on figures.
 
Following table explains marking used on figures.
 
{|{{prettytable}}
 
{|{{prettytable}}
Line 9: Line 9:
 
|2||Doorphone speaker cover
 
|2||Doorphone speaker cover
 
|-
 
|-
−
|3||Hole for microphone installed in doorphone
+
|3||Blind hole
 
|-
 
|-
−
|4||Address window
+
|4||Blind holes
 
|-
 
|-
−
|5||Establish call button
+
|5||Address window
 
|-
 
|-
−
|6||Mark, informing about RFID card reader
+
|6||Establish call button
 +
|-
 +
|7||Hole for microphone installed in doorphone
 +
|-
 +
|8||Indicator doorphone RFID card reader
 
|-
 
|-
 
|}
 
|}
−
{{warning|If in doorphones, which include embedded RFID card reader, you use card with standard credit card dimensions, it is enough to approach this card to 5 - 6cm from doorphone, in parallel to doorphone, bellow speaker so over PCB presented on following figure. Jeżeli natomiast, jako kart RFID, używamy małych breloczków - zalecamy zbliżyć je na odległość 1cm w miejscu, gdzie znajduje się znaczek oznaczony na powyższych rysunkach cyfrą 6.}}
+
 
−
Do panelu przedniego przykręcona jest płytka z elementami elektronicznymi. Widoczna jest ona po zdjęciu panelu przedniego. Wszelkie elementy niezbędne do instalacji bramofonu są widoczne, dostępne i nie jest konieczne odkręcanie płytki elektroniki od panelu przedniego. Widok płytki elektroniki przykręconej do panelu przedniego prezentuje poniższy rysunek:
+
 
 +
{{warning|
 +
If in doorphones, which include embedded RFID card reader, you use card with standard credit card dimensions, it is enough to approach this card to 5 - 6cm from doorphone, in parallel to doorphone, bellow speaker so over PCB presented on below figure. If you use small pendants as RFID card, it is recommended to aproach such pendant to 1cm in place where there is mark described as 8 on above figures.}}
 +
 
 +
 
 +
To front panel the PCB board is fixed. It is visible after removing front panel. All elements neccessarily to doorphone installation are accessible and it is not needed to remove PCB from front panel. View of PCB fixed to front panel is presented on following figure:
 +
 
 +
 
 
<center>[[File:DPH KS1(2) wnetrze.png]]</center>
 
<center>[[File:DPH KS1(2) wnetrze.png]]</center>
 +
 +
 +
Tags used in the drawing are explained in the following table.
 +
 +
{|{{prettytable}}
 +
!{{Hl2}}|Number !!{{Hl2}}| Meaning
 +
|-
 +
|1||Camera connection connector (not used)
 +
|-
 +
|2||Loudspeaker connector
 +
|-
 +
|3||USB connector
 +
|-
 +
|4||Jumper used when programming the doorphone
 +
|-
 +
|5||Connector for doorphone connection
 +
|-
 +
|6||Microphone connector
 +
|-
 +
|}

Latest revision as of 13:33, 1 June 2020

Front panel of DPH doorphone is fixed by wrench srews M4, included in purchased set. Location of these screws is marked by digit 1, visible on below figures.

DPH.AB-KS1RF.DG oznaczenia.pngDPH.AB-KS2RF.C oznaczenia.DG.png

Following table explains marking used on figures.

Digit Significance
1 Screws for fixing front panel
2 Doorphone speaker cover
3 Blind hole
4 Blind holes
5 Address window
6 Establish call button
7 Hole for microphone installed in doorphone
8 Indicator doorphone RFID card reader


Warning!

If in doorphones, which include embedded RFID card reader, you use card with standard credit card dimensions, it is enough to approach this card to 5 - 6cm from doorphone, in parallel to doorphone, bellow speaker so over PCB presented on below figure. If you use small pendants as RFID card, it is recommended to aproach such pendant to 1cm in place where there is mark described as 8 on above figures.


To front panel the PCB board is fixed. It is visible after removing front panel. All elements neccessarily to doorphone installation are accessible and it is not needed to remove PCB from front panel. View of PCB fixed to front panel is presented on following figure:


DPH KS1(2) wnetrze.png


Tags used in the drawing are explained in the following table.

Number Meaning
1 Camera connection connector (not used)
2 Loudspeaker connector
3 USB connector
4 Jumper used when programming the doorphone
5 Connector for doorphone connection
6 Microphone connector
Retrieved from "https://pubwiki.slican.com/index.php?title=DPH_-_Opening_doorphone_casing&oldid=7875"