Difference between revisions of "DPH - Doorphone DPH.AB-KS16 programming"

From pubWiki-en
Jump to: navigation, search
(→‎DPH16 - Menu structure)
(→‎DPH16 - Programming using DTMF code)
 
(55 intermediate revisions by 2 users not shown)
Line 4: Line 4:
 
* Using doorphone keyboard and display - local programming.
 
* Using doorphone keyboard and display - local programming.
 
Using DTMF menu there is no possible to program all options, especially options which require reaction. Additionally local menu enables programming both admin and user options - user options are set by every user individually.  
 
Using DTMF menu there is no possible to program all options, especially options which require reaction. Additionally local menu enables programming both admin and user options - user options are set by every user individually.  
 +
==PIN code==
 +
Every DPH doorphone can be equipped in PIN code. By default there is no PIN code, PIN code can be used to protect DPH against unathorized access. You can define PIN code using DTMF code according table included in chapter [[DPH_-_Doorphone_DPH.AB-KS16_programming#DPH16 - Programming using DTMF code |concerning DTMF programing]].
 +
{{warning|If you have no PIN code, it is possible to enter in DTMF menu only when SETUP jumper is inserted.}}
 +
 
== DPH16 - Programming using DTMF code ==
 
== DPH16 - Programming using DTMF code ==
 
DTMFb menu structure in DPH doorphone is based on solution implemented in Slican PMS.
 
DTMFb menu structure in DPH doorphone is based on solution implemented in Slican PMS.
−
* Entering to programming menu - during call digits '''0987''' should be dialed.
+
* Entering to programming menu - during call digits '''0987''' should be dialed. <ref name="noPIN">If there is no PIN code defined, there is no possibility to enter in DTMF nenu.</ref>
 
* All programming options are organized in XY array.
 
* All programming options are organized in XY array.
 
* After pressing *, in every moment, entered parameter is canceled and program returns to XY coordinates selection.
 
* After pressing *, in every moment, entered parameter is canceled and program returns to XY coordinates selection.
 
* After pressing # entered parameter is confirmed.
 
* After pressing # entered parameter is confirmed.
 
* After pressing asterisk two times program mode is leaving.
 
* After pressing asterisk two times program mode is leaving.
 +
* After program mode leaving connection established for programming is disconnected
 
* After dialing XY coordinates (programming option) confirmation (high frequency) or reject (low frequency) signal is generated.
 
* After dialing XY coordinates (programming option) confirmation (high frequency) or reject (low frequency) signal is generated.
 
* Entering program mode is possible if jumper SETUP is ON.
 
* Entering program mode is possible if jumper SETUP is ON.
Line 27: Line 32:
 
!'''4'''
 
!'''4'''
 
!'''5'''
 
!'''5'''
−
!'''...'''
+
!'''6'''
 +
!'''7'''
 
!'''9'''
 
!'''9'''
 
! '''Parameter description'''
 
! '''Parameter description'''
Line 54: Line 60:
 
||Short
 
||Short
 
number
 
number
−
'''...''' '''[none]'''
+
'''6''' '''[none]'''
 +
||Short
 +
number
 +
'''7''' '''[none]'''
 
||Short
 
||Short
 
number
 
number
Line 72: Line 81:
 
None - any number
 
None - any number
 
||'''Max call time [180]'''
 
||'''Max call time [180]'''
−
10..360 sec
+
10..9000 sec
 
||'''Finish call [0]'''  
 
||'''Finish call [0]'''  
 
0 - none
 
0 - none
Line 84: Line 93:
 
'#' confirm
 
'#' confirm
 
Next DPH reset
 
Next DPH reset
−
||'''Autoconfirmation time [10]''' 0..60sec
+
||'''Confirm. time [10]''' 0..60sec
−
||
+
||'''Call begin button [0]'''
 +
 
 +
0 - none
 +
 
 +
1 - POD
 +
 
 +
2 - COD
 +
 
 +
Short number 0 is dialed.
 +
||'''Auto answer [1]'''
 +
0 - NO
 +
 
 +
1 - YES
 
||
 
||
 
||'''Dialed numbers features'''
 
||'''Dialed numbers features'''
Line 98: Line 119:
 
1 - electromagnetic keeper
 
1 - electromagnetic keeper
 
||'''STA opening time [2]'''
 
||'''STA opening time [2]'''
−
1..60 sec
+
1..360 sec
 
||'''DTMF * receiving [3]'''
 
||'''DTMF * receiving [3]'''
 
0 - no action
 
0 - no action
Line 115: Line 136:
  
 
3 - EZ and STA opening
 
3 - EZ and STA opening
−
||'''x'''
+
||'''STA mode[0]'''
 +
0 - Gate mode
 +
 
 +
1 - Light mode
 +
||'''SHK mode [0]'''
 +
0 - SHK off<br>
 +
1- Button 1 - SHK<br>
 +
2- Button 2 - SHK<br>
 +
3- Button 1 and 2 - SHK<br>
 
||
 
||
 
||
 
||
Line 139: Line 168:
  
 
2 - high
 
2 - high
 +
||'''Switch level [2]'''
 +
0..8
 +
Minimal value of speak direction switching level
 
||
 
||
 
||
 
||
Line 161: Line 193:
 
|| '''x'''
 
|| '''x'''
  
 +
||
 
||
 
||
 
||
 
||
Line 167: Line 200:
 
||
 
||
 
||'''RFID cards'''  
 
||'''RFID cards'''  
 +
|-
 +
||6
 +
|| '''PIN change'''
 +
Entering 4 digits PIN code
 +
Entering method:
 +
PPPP#PPPP#, P- any PIN digit 0..9, # - hash in DTMF
 +
 +
For sequence ## - erasing PIN (no PIN)
 +
 +
PIN entered in DTMF is equal to admin PIN entered from DPH16 keyboard.
 +
 +
||
 +
||
 +
||
 +
||
 +
||
 +
||
 +
||
 +
||
 +
||'''PIN'''
 +
  
 
|}
 
|}
Line 174: Line 228:
 
* XY coordinates confirmation - button HASH (#)
 
* XY coordinates confirmation - button HASH (#)
 
* Parameter entering can be always canceled by STAR (*) button. as a result low frequency signal (BAD) is generated and jump to coordinates selecting
 
* Parameter entering can be always canceled by STAR (*) button. as a result low frequency signal (BAD) is generated and jump to coordinates selecting
−
* ZConfirmation of any parameter can be done with HASH (#) button. If parameter value is correct and parameterr was succesfully stored in FLASH memory - high frequency signal (OK) is generated and dorphone waits for coordinates selection.
+
* Confirmation of any parameter can be done with HASH (#) button. If parameter value is correct and parameterr was succesfully stored in FLASH memory - high frequency signal (OK) is generated and dorphone waits for coordinates selection.
 
* If parameter value is incorrect - low frequency signal (BAD) is generated and dorphone waits for coordinates selection.
 
* If parameter value is incorrect - low frequency signal (BAD) is generated and dorphone waits for coordinates selection.
 
* Max call time - new value is obvious for next call
 
* Max call time - new value is obvious for next call
 
* Autoconfirmation time - time needed to automatic confirmation entered number. If 0, after 20 seconds entered number will be canceled.
 
* Autoconfirmation time - time needed to automatic confirmation entered number. If 0, after 20 seconds entered number will be canceled.
 +
* Parameter '''Switch level''' operating in following manner: phone signal strenght must be proportional to value of this parameter to be hear in doorphone speaker. Change of this parameter is helpful for calls quality if noise generated in phone premise is very high. While to low swithing level voice from doorphone can be interrupted. Configuration range is between 0 and 8, default value is equal to 2. Correct value should be set according experiment, individually fot every doorphone location.
 +
* If value of STA mode option is equal to 0, active are STA control by RFID, PINu and DTMF, otherwise if value of STA mode option is set to 1, only only pressing any button or answering incoming call can trigger STA output.
 +
* If value of option Auto answer is equal to 0, an incoming call can't be answered by doorphone. In this situation, doorphone DTMF programming is possible only after establishing call from doorphone to phone.
  
 
== DPH16 - Service menu maintenance ==
 
== DPH16 - Service menu maintenance ==
Line 186: Line 243:
 
* With navigation buttons- [[File:DPH16-Up.PNG|30px]] and [[File:DPH16-Down.PNG|34px]] select "Service" menu.
 
* With navigation buttons- [[File:DPH16-Up.PNG|30px]] and [[File:DPH16-Down.PNG|34px]] select "Service" menu.
 
* Confirm selection by pressing [[File:DPH16-call.PNG|30px]] button.
 
* Confirm selection by pressing [[File:DPH16-call.PNG|30px]] button.
−
* Doorphone asks about PIN code. By default this code is equal to last four digits of doorphone serial number - using this menu this PIN code can be changed, but it always consists of 4 digits. After entering 4th digit - if entered PIN code is correct - on doorphone first option of first menu level is displayed. All menu levels and options on every menu level are presented in this chapter, in paragraph about menu structure. While entering wrong PIN, signal coonfirming entering last character is generated, but frequency of this signal is different (lower) than nolmally.
+
* Doorphone asks about PIN code. By default there is no PIN code, to enter this menu. To enter service menu you can insert SETUP jumper<ref name="SETUP">If SETUP jumper is inserted and there is no PIN code defined, DPH.AB-KS16 is always in service menu and there is no possibility to normal DPH operation.</ref>. If PIN code is defined, after entering 4th digit - if entered PIN code is correct - on doorphone first option of first menu level is displayed. All menu levels and options on every menu level are presented in this chapter, in paragraph about menu structure. While entering wrong PIN, signal coonfirming entering last character is generated, but frequency of this signal is different (lower) than nolmally.
 
=== DPH16 - Menu structure ===
 
=== DPH16 - Menu structure ===
 
As mentioned in previous paragraph, after entering proper PIN code, on doorphone display firsyt option of first menu level is visible - here is option "Names". Using buttons [[File:DPH16-Up.PNG|30px]] and [[File:DPH16-Down.PNG|30px]] you can navigate between options of specified menu level. Specified option can be selected by pressing [[File:DPH16-call.PNG|30px]] button, next menu level is displayed (according below figure) or selected option can be edited (if this option is not assigned to any next menu level). After pressing button [[File:DPH16-end.PNG|30px]] previous level menu is selected or edition mode canceled without saving entered data. If you press button [[File:DPH16-C.PNG|30px]] during edition of specified option, last entered character will be erased.
 
As mentioned in previous paragraph, after entering proper PIN code, on doorphone display firsyt option of first menu level is visible - here is option "Names". Using buttons [[File:DPH16-Up.PNG|30px]] and [[File:DPH16-Down.PNG|30px]] you can navigate between options of specified menu level. Specified option can be selected by pressing [[File:DPH16-call.PNG|30px]] button, next menu level is displayed (according below figure) or selected option can be edited (if this option is not assigned to any next menu level). After pressing button [[File:DPH16-end.PNG|30px]] previous level menu is selected or edition mode canceled without saving entered data. If you press button [[File:DPH16-C.PNG|30px]] during edition of specified option, last entered character will be erased.
  
 
Following figure presents doorphone menu structure with all options on every menu level.
 
Following figure presents doorphone menu structure with all options on every menu level.
−
[[File:DPHMenuSevice.png]]
+
[[File:DPHMenuSevice1.25.png]]<br>
−
* Names - this option is used to define up to 10 names, to which numbers (internal or external) dialed by doorphone after selecting specified name are assigned.
+
'''Names''' - this option is used to define up to 50 names, to which numbers (internal or external) dialed by doorphone after selecting specified name are assigned.
−
** Name 0 .. Name 9 - After selecting one ot these options you can enter any name (including maximally 20 characters), after selecting this name, doorphone dials number assibned to this name. If you press button [[File:DPH16-call.PNG|30px]], when specified name is on display, edition of this name is started.
+
* Screen text - editable text, which will be displayd on screen in idle status.
−
* Numbers - this option is used to define numbers dialed by doorphone after selecting Name 0...Name 9.
+
** text is displayed on screen in place od short number,
−
** Number 0 .. Number 9 - after selecting one of these options you can enter any number(including maximally 16 digits), this number will be dialed by doorphone if you select appropriate Name 0 - ...9, Number 0 is assigned to  Name 0 etc.
+
** no possibility to make a call on idle screen (to make a call it is necessary to search a short number using [[Plik:DPH16-Down.PNG|30px]] or [[Plik:DPH16-Up.PNG|30px]] keys, and then press [[Plik:DPH16-call.PNG|30px]]),
−
** Hot line - selecting this option enables to define hot line as as one of numbers. Ex. if in edition mode number 2 was defined as hot line, after selecting Name 2 from doorphone keyboard, only simulation of lifting handset will be performed, number defined as Number 2 will not be dialed. It should be remembered, that numer name defined as hot line must be defined. If this number is not defined, there is not possible to select name defined as hot line.
+
** below the screen text, there is "Search" text displayed, but only if there is at least one short number on the list and "search" text displaying is turned on (Setting -> Show "Search").
−
* Settings - this option enables to set several doorphone parameters
+
Maximum lenght of the text is 64 digits. Text is centered in default, but it can be aligned to the left or right by putting '''\l''' or '''\r''' letter in front of the text. Text can be enforced to the next line by typig '''/n''' before the text.
−
** Dialing time - this parameter defines time in seconds, after this time number entered from keyboard is dialed by doorphone, even if entering number is not confirmed by pressing [[File:DPH16-call.PNG|30px]] button. By default this time is set to 10s.
+
 
−
** Call time - this option enebles to set maximal time of call established between doorphone and any phone. By default this time is set to 180s. It should be noticed, that doorphone is equipped in busy signal detector and call is automatically disconnected after hanging off handset of phone connected to doorphone.
+
* Name 0 .. Name 49 - After selecting one ot these options you can enter any name (including maximally 20 characters), after selecting this name, doorphone dials number assibned to this name. If you press button [[File:DPH16-call.PNG|30px]], when specified name is on display, edition of this name is started.
−
** Add # - this option enables to add # after number dialed by doorphone. It is important if PBX works in slow number analisys mode andafter entering last number digit PBX waits for time of slow number analisys, before dialing this number. Character # added on number end eliminates this time.
+
'''Number''' - this option is used to define numbers dialed by doorphone after selecting Name 0...Name 9.
−
** EZ time - this option enables to set the time (in seconds) of opening electrolock connected to doorphone, this time defines how long the electrolock is open after sending 1, or * sign (if EZ openinig was defined as "DTMF action"). By default this time is equal to 3s.
+
** Number 0 .. Number 49 - after selecting one of these options you can enter any number(including maximally 16 digits), this number will be dialed by doorphone if you select appropriate Name 0 - ...9, Number 0 is assigned to  Name 0 etc.
−
** EZ mode - this option enables to set electrolock working mode. Two different working mode are possible:
+
* Hot line - selecting this option enables to define hot line as as one of numbers. Ex. if in edition mode number 2 was defined as hot line, after selecting Name 2 from doorphone keyboard, only simulation of lifting handset will be performed, number defined as Number 2 will not be dialed. It should be remembered, that numer name defined as hot line must be defined. If this number is not defined, there is not possible to select name defined as hot line.
−
*** Electrolock - for this option, during the time defined as "EZ time" parameter, 12V voltage is connected to electrolock terminals.
+
'''Settings''' - this option enables to set several doorphone parameters
−
*** Electromagnetic keeper - for this option, 12V voltage is connected continously to electrolock terminals, however after opening door by the time defined by "EZ time" parameter, this voltage is not connected to electrolock terminals.
+
* Dialing time - this parameter defines time in seconds, after this time number entered from keyboard is dialed by doorphone, even if entering number is not confirmed by pressing [[File:DPH16-call.PNG|30px]] button. By default this time is set to 10s.
−
** STA time - this option enables to set time (in seconds) of trigger additional relay connected to doorphone, after sending character 2 or * (if trigger this relay is defined as "DTMF action"). By default this time is set to 2s.
+
* Call time - this option enebles to set maximal time of call established between doorphone and any phone. By default this time is set to 180s. It should be noticed, that doorphone is equipped in busy signal detector and call is automatically disconnected after hanging off handset of phone connected to doorphone.
−
** Test EZ&STA - it is typical service option, it tests if doorphone trigerr EZ and STA outputs. After selecting this option, menu including three followiung options is displayed on doorphone display:
+
* Add # - this option enables to add # after number dialed by doorphone. It is important if PBX works in slow number analisys mode andafter entering last number digit PBX waits for time of slow number analisys, before dialing this number. Character # added on number end eliminates this time.
−
*** EZ output - after selecting this option an output with electrolock connected to is triggered
+
* Only short No. - when this option is turned on, only short numbers are available to dial. First 10 numbers are accessible from keypad keys, and rest rest can be searched with [[Plik:DPH16-Up.PNG|30px]] and [[Plik:DPH16-Down.PNG|30px]] keys.
−
*** STA output - after selecting this option an output with additional relay STA connected is trigerred
+
* Auto Answer - all incoming calls will be automatically answered.
−
*** EZ&STA output - after selecting this option outputs EZ and STA are trigerred in the same time
+
* Show "Search" - turning option off will erase search text from screen. Recommended, when screen text is longer than 3 lines.
−
** DTMF action - this option enables to define type of action performed after sending * to doorphone. After selecting this option, menu including four following options is displayed on doorphone display:
+
* EZ time - this option enables to set the time (in seconds) of opening electrolock connected to doorphone, this time defines how long the electrolock is open after sending 1, or * sign (if EZ openinig was defined as "DTMF action"). By default this time is equal to 3s.
−
*** None - no action is performed after sending * to doorphone
+
* EZ mode - this option enables to set electrolock working mode. Two different working mode are possible:
−
*** EZ open - after sending * to doorphone EZ output is trigerred
+
** Electrolock - for this option, during the time defined as "EZ time" parameter, 12V voltage is connected to electrolock terminals.
−
*** STA open - after sending * to doorphone STA output is trigerred
+
** Electromagnetic keeper - for this option, 12V voltage is connected continously to electrolock terminals, however after opening door by the time defined by "EZ time" parameter, this voltage is not connected to electrolock terminals.
−
*** EZ&STA open - after sending * to doorphone EZ and STA output are trigerred
+
* STA time - this option enables to set time (in seconds) of trigger additional relay connected to doorphone, after sending character 2 or * (if trigger this relay is defined as "DTMF action"). By default this time is set to 2s.
−
** RFID action - othis option enables to define type of action performed after approach of registered RFID card. After selecting this option, menu including four following options is displayed on doorphone display:
+
* STA mode - this option define type of device connected to STA output. If value of STA mode option is equal to 0, STA output is trigged by RFID, PINu and DTMF, otherwise if value of STA mode option is set to 1, only pressing any button or answering incoming call can trigger STA output.
−
*** None- no action is performed after approach of registered RFID card
+
* Test EZ&STA - it is typical service option, it tests if doorphone trigerr EZ and STA outputs. After selecting this option, menu including three followiung options is displayed on doorphone display:
−
*** EZ open - after approach of registered RFID card EZ ootput is trigerred
+
** EZ output - after selecting this option an output with electrolock connected to is triggered
−
*** STA oopen - after approach of registered RFID card EZ and STA ootput are trigerred
+
** STA output - after selecting this option an output with additional relay STA connected is trigerred
−
*** EZ&STA open - after approach of registered RFID card STA ootput is trigerred
+
** EZ&STA output - after selecting this option outputs EZ and STA are trigerred in the same time
−
** Call end - this option enables to finish call as a result of local action, no matter what is a status of phone connected with doorphone. After selecting this option, menu including four following options is displayed on doorphone display:
+
* DTMF action - this option enables to define type of action performed after sending * to doorphone. After selecting this option, menu including four following options is displayed on doorphone display:
−
*** None - connection with doorphone will be finished only after hang off the handset of the phone connected to doorphone or after time defined by "Call time" parameter.
+
** None - no action is performed after sending * to doorphone
−
*** POD - connection with doorphone will be finished after hang off the handset of the phone connected to doorphone or after time defined by "Call time" parameter or after pressing POD button.  
+
** EZ open - after sending * to doorphone EZ output is trigerred
−
*** COD - connection with doorphone will be finished after hang off the handset of the phone connected to doorphone or after time defined by "Call time" parameter or after COD sensor triger.
+
** STA open - after sending * to doorphone STA output is trigerred
−
*** POD or COD - connection with doorphone will be finished after hang off the handset of the phone connected to doorphone or after time defined by "Call time" parameter, after pressing POD button or after COD sensor triger.
+
** EZ&STA open - after sending * to doorphone EZ and STA output are trigerred
−
** Language - after selecting this option it is possible to set language of communication between doorphone and user. Possible is Polish and English language.
+
* RFID action - othis option enables to define type of action performed after approach of registered RFID card. After selecting this option, menu including four following options is displayed on doorphone display:
−
** LCD contrast - selecting this option enables to set contrast of LCD display, in 11-stage scale. By default 6 stage is set.
+
** None- no action is performed after approach of registered RFID card
−
** Factory settings - selecting this option enables to restore doorphone factory settings. Before restore factory settings, doorphone ask about selection confirmation.
+
** EZ open - after approach of registered RFID card EZ ootput is trigerred
−
** About - selecting this option enables to present version of software uploaded to doorphone, this software creation date and author info.
+
** STA oopen - after approach of registered RFID card EZ and STA ootput are trigerred
−
* Acoustic - this option is used to doorphone acoustic parameter set.  
+
** EZ&STA open - after approach of registered RFID card STA ootput is trigerred
−
** SPK volume - this option is used to set doorphone speaker volume in 7-stage scale. By default 3 stage is set.
+
* Call end - this option enables to finish call as a result of local action, no matter what is a status of phone connected with doorphone. After selecting this option, menu including four following options is displayed on doorphone display:
−
** MIC sens - othis option is used to set doorphone microphone sensitivity in tri stage scale Low, Medium, High. By default Medium sensitivity is set.
+
** None - connection with doorphone will be finished only after hang off the handset of the phone connected to doorphone or after time defined by "Call time" parameter.
−
* Accounts - selecting this option enables to create and erase user accounts and display parameters set for this accounts. After selecting this option, menu including following options is displayed on doorphone display:
+
** POD - connection with doorphone will be finished after hang off the handset of the phone connected to doorphone or after time defined by "Call time" parameter or after pressing POD button.  
−
** Show - after selecting this option, caption "Account number" and number of already created account are displayed on doorphone display. Such display status is about 2 seconds and then first of registered accounts as well as context menu "Option" and "Exit" are displayed on doorphone display. After press button [[File:DPH16-end.PNG|30px]] you go back to menu "Accounts", while after press button [[File:DPH16-call.PNG|30px]] next menu appears on display. It includes following options:
+
** COD - connection with doorphone will be finished after hang off the handset of the phone connected to doorphone or after time defined by "Call time" parameter or after COD sensor triger.
−
*** New PIN - this option enables to change user PIN code. After selecting this option, doorphone asks to enter new PIN code and next after its confirmation using button [[File:DPH16-call.PNG|30px]], asks about once more entering new PIN code. After second entering, if both entered PIN codes are identical, doorphone stores ne PIN code, however if entered PIN codes are different user hears audio tone with low frequency and captioon "Mismatch PIN" appears on doorphone display
+
** POD or COD - connection with doorphone will be finished after hang off the handset of the phone connected to doorphone or after time defined by "Call time" parameter, after pressing POD button or after COD sensor triger.
−
*** New RFID - this option enables to assign new RFID card to user account, using this card it is possible to perform action defined as "RFID action". After selecting this option doorphone asks about approaching RFIPD card. <BR><B>Attention!</B> Card registered in doorphone should have the unique ID, so it is impossible to assign the same card to two different user accounts. Symilarly it is not possible to register two different cards to one user account. Card assigned as second replaces earlier assigned card.
+
* Language - after selecting this option it is possible to set language of communication between doorphone and user. Possible is Polish and English language.
−
*** Remove RFID - this option enables to remove already assigned RFID card. After selecting this option doorphone asks about remove confirmation using button [[File:DPH16-call.PNG|30px]], after confirmation assigned card is removed. Pressing button [[File:DPH16-end.PNG|30px]] returns to option "Remove RFID" without removing  bez usuwania istniejącego przypisania.
+
* LCD contrast - selecting this option enables to set contrast of LCD display, in 11-stage scale. By default 6 stage is set.
−
*** Delete account - this option enables to delete specified user account with all data assigned to this account. After selecting this option doorphone asks about delete confirmation using button [[File:DPH16-call.PNG|30px]], after confirmation specified account is deleted. Pressing button [[File:DPH16-end.PNG|30px]] returns to option "Delete account" without deleting account.
+
* Factory settings - selecting this option enables to restore doorphone factory settings. Before restore factory settings, doorphone ask about selection confirmation.
−
*** Add account - this option enables to add an account, if account is not registered yet. Method of naming accounts defined in doorphone DPH.AB-KS16 is strictly determined. Account name consists always with caption "Account" and number from range 1..9999, including always four digits. Total number of accounts defined in doorphone cannot increase above 512. After selecting this option doorphone suggests number one more than higher created number. User who add new account can of course change proposed number (world "Account" cannot be changed), but if account with entered number already exists, doorphone informs about it. W przypadku, gdy konto o najwyższym numerze (9999) już istnieje, bramofon zaproponuje utworzenie konta o najwyższym wolnym numerze. Po ewentualnej zmianie proponowanego przez bramofon numeru tworzonego konta należy je utworzyć, naciskając klawisz [[File:DPH16-call.PNG|30px]]. Bramofon poinformuje o zrealizowaniu polecenia komunikatem "Konto xxxx utworzone" gdzie xxxx jest numerem utworzonego konta. Jeżeli konto o wprowadzonym numerze istnieje, to bramofon zgłosi to komunikatem "Podane konto istnieje". Jeżeli ilość zdefiniowanych kont przekracza 512, na wyświetlaczu pojawi się napis "Zbyt dużo kont".
+
* About - selecting this option enables to present version of software uploaded to doorphone, this software creation date and author info.
−
** Dodaj - opcja ta pozwala na stworzenie nowego konta. Zasady oznaczania oraz tworzenia nowych kont przy wykorzystaniu tej opcji są identyczne jak w opisano w powyższym paragrafie.
+
'''Acoustic''' - this option is used to doorphone acoustic parameter set.  
−
** Usuń - opcja ta pozwala na usunięcie błędnie wprowadzonego lub niewykorzystywanego już konta. Po wybraniu tej opcji na ekranie pojawia się lista zdefiniowanych kont. Można je wybierać klawiszami [[File:DPH16-Up.PNG|30px]] oraz [[File:DPH16-Down.PNG|30px]], po wybraniu konta do usunięcia, naciskamy klawisz [[File:DPH16-call.PNG|30px]], co spowoduje usunięcie konta potwierdzone komunikatem "Konto xxxx usunięte".
+
* SPK volume - this option is used to set doorphone speaker volume in 7-stage scale. By default 3 stage is set.
−
** Nr Tabeli PIN -  w momencie dodawania konta opisanego powyżej, bramofon generuje dla każdego konta czterocyfrowy kod PIN, który służy zarówno do otwierania bramy, jak i wejścia w menu użytkownika. Numer kodu PIN użytkownika generowany jest na podstawie nr tabeli kodów PIN, zapisanego w tej właśnie opcji. Należy pamiętać, że możliwe jest wygenerowanie części kodów PIN w oparciu o pewien numer tabeli, druga część natomiast może zostać wygenerowana w oparciu o inny nr tabeli. Nr tabeli jest zawsze czterocyfrowy, jeżeli użytkownik korzystając z tej opcji wprowadzi mniej cyfr niż cztery, bramofon automatycznie uzupełni ten numer poprzez dodanie odpowiedniej ilości zer nieznaczących.Standardowo numer ten jest określony jako 1234.
+
* MIC sens - othis option is used to set doorphone microphone sensitivity in tri stage scale Low, Medium, High. By default Medium sensitivity is set.
−
** Generuj - opcja ta pozwala na automatyczne wygenerowanie większej ilości kont, wraz z przypisaniem im kodów PIN na podstawie tabeli o numerze zdefiniowanym poprzednią opcją.
+
'''Accounts''' - selecting this option enables to create and erase user accounts and display parameters set for this accounts. After selecting this option, menu including following options is displayed on doorphone display:
−
* Serwis - opcja ta pozwala na zmianę parametrów, które pozwalają na wejście w menu administratora. Po wybraniu tej opcji na wyświetlaczu pojawia się menu niższego poziomu, zawierające trzy opcje:
+
* Show - after selecting this option, caption "Account number" and number of already created account are displayed on doorphone display. Such display status is about 2 seconds and then first of registered accounts as well as context menu "Option" and "Exit" are displayed on doorphone display. After press button [[File:DPH16-end.PNG|30px]] you go back to menu "Accounts", while after press button [[File:DPH16-call.PNG|30px]] next menu appears on display. It includes following options:
−
** Zmień PIN -  wybranie tej opcji pozwala na zmianę kodu PIN pozwalającego na wejście do menu serwisowego. Po wybraniu tej opcji bramofon poprosi o wprowadzeniu nowego kodu PIN. Po wprowadzeniu czwartej cyfry kodu PIN (kod musi posiadać cztery cyfry) konieczne jest ponowne wprowadzenie tego kodu. Jeżeli obydwa wprowadzone kody są identyczne, kod PIN zostanie zmieniony, co zostanie potwierdzone odpowiednim komunikatem na wyświetlaczu. Jeżeli wprowadzone kody nie są identyczne, na wyświetlaczu bramofonu pojawi się napis "Niezgodny PIN" i kod PIN nie zostanie mieniony
+
** New PIN - this option enables to change user PIN code. After selecting this option, doorphone asks to enter new PIN code and next after its confirmation using button [[File:DPH16-call.PNG|30px]], asks about once more entering new PIN code. After second entering, if both entered PIN codes are identical, doorphone stores ne PIN code, however if entered PIN codes are different user hears audio tone with low frequency and captioon "Mismatch PIN" appears on doorphone display
−
** Ustaw RFID - po wybraniu tej opcji bramofon poprosi o zbliżenie karty RFID i zarejestruje ją jako kartę serwisową. Od tego momentu możliwe będzie wchodzenie do menu administratora w wyniku przyłożenia do bramofonu tej karty, bez potrzeby podawania kodu PIN administratora.
+
** New RFID - this option enables to assign new RFID card to user account, using this card it is possible to perform action defined as "RFID action". After selecting this option doorphone asks about approaching RFID card. <BR><B>Attention!</B> Card registered in doorphone should have the unique ID, so it is impossible to assign the same card to two different user accounts. Symilarly it is not possible to register two different cards to one user account. Card assigned as second replaces earlier assigned card.
−
** Usuń RFID - po wybraniu tej opcji, bramofon poprosi o potwierdzenie chęci usunięcia karty RFID. Po potwierdzeniu klawiszem [[File:DPH16-call.PNG|30px]], zarejestrowana karta zostanie usunięta.
+
** Remove RFID - this option enables to remove already assigned RFID card. After selecting this option doorphone asks about remove confirmation using button [[File:DPH16-call.PNG|30px]], after confirmation assigned card is removed. Pressing button [[File:DPH16-end.PNG|30px]] returns to option "Remove RFID" without removing  bez usuwania istniejącego przypisania.
 +
** Delete account - this option enables to delete specified user account with all data assigned to this account. After selecting this option doorphone asks about delete confirmation using button [[File:DPH16-call.PNG|30px]], after confirmation specified account is deleted. Pressing button [[File:DPH16-end.PNG|30px]] returns to option "Delete account" without deleting account.
 +
** Add account - this option enables to add an account, if account is not registered yet. Method of naming accounts defined in doorphone DPH.AB-KS16 is strictly determined. Account name consists always with caption "Account" and number from range 1..9999, including always four digits. Total number of accounts defined in doorphone cannot increase above 512. After selecting this option doorphone suggests number one more than higher created number. User who add new account can of course change proposed number (world "Account" cannot be changed), but if account with entered number already exists, doorphone informs about it. If account with highest possible number (9999) already exists, doorphone proposes to create an account with highest free number. After eventually change of proposed by doorphone number, new account should be created by pressing button [[File:DPH16-call.PNG|30px]]. Doorphone informs about creating account with message "Account xxxx created" where xxxx is number of created account. If account with entered number already exists, doorphone informs about it with message "Entered acc. exists". If number of defined accounts is beyond 512, caption "To many acc".
 +
** Add - this option enables to create new account. Rules of creating new accounts are the same as in above point.
 +
** Delete - this option enables to delete wrongly entered or unused account. After selecting this option, list of accounts is displayed on doorphone display. They can be selected with buttons [[File:DPH16-Up.PNG|30px]] and [[File:DPH16-Down.PNG|30px]], after selecting account to delete, press button [[File:DPH16-call.PNG|30px]], it deletes specified account with confirmation message "Account xxxx deleted".
 +
** PIN table No -  while adding new account as described above, doorphone generates four digits PIN code for every account, this PIN code is used to opening door and to enter in user menu. PIN code is generated according table of PIN codes, this option is used to determine this number. It is possible to generate some PIN codes according one PIN table number, and another part of numbers can be generated according another PIN table number. Table number is always four digits, if user with this option enter less than four digits, doorphon automatically adds appropriate number of digit 0 at the begining of entered number. By default this number is equal to 1234.
 +
** Generate - this option enables to genetrate more than one account and assigning PIN codes to these accounts.
 +
'''Service''' - this option enables to change parameters, which enable to enter into service menu. After selecting this option, menu including three following options is displayed on doorphone display:
 +
* Change PIN -  selecting this option enables to change PIN code, which enables enter to service menu. After selecting this option doorphone asks about entering new PIN code. After entering fourth digit of PIN code (PIN code must consists of four digits) it is necessarily to entering this code once more. If both entered codes are identical, PIN code will b e changed, it is confirmed by appropriate message on doorphone display, however if entered PIN codes are different user hears audio tone with low frequency and caption "Mismatch PIN" appears on doorphone display
 +
* Set RFID - after selecting this option doorphone asks about approaching RFID card and registers it as service cerd. From this moment it is possible to entering into service menu as a result of approaching this card to doorphoe without entering service PIN code.
 +
* Del RFID - after selecting this option doorphone asks about confirmation of deleting RFID card. After confirmation with button [[File:DPH16-call.PNG|30px]], registered card is deleted.
  
 
== DPH16 - User menu maintenance ==
 
== DPH16 - User menu maintenance ==
−
Wejście w menu użytkownika odbywa się następująco:
+
Etering into user menu can be done as follows:
−
* Naciśnij dwukrotnie klawisz [[File:DPH16-Kluczyk.PNG|30px]].
+
* Press two times button [[File:DPH16-Kluczyk.PNG|30px]].
−
* Klawiszami nawigacyjnymi [[File:DPH16-Up.PNG|30px]] and [[File:DPH16-Down.PNG|34px]] wybrać menu "UŻYTKOWNIKA".
+
* With navigation keys [[File:DPH16-Up.PNG|30px]] and [[File:DPH16-Down.PNG|34px]] select option "USER".
−
* Zatwierdzić wybór, naciskając klawisz [[File:DPH16-call.PNG|30px]].
+
* Confirm selection by pressing button [[File:DPH16-call.PNG|30px]].
−
* Bramofon poprosi wówczas o wybranie konta użytkownika, którego parametry chcemy zmieniać. Za pomocą klawiszy nawigacyjnych [[File:DPH16-Up.PNG|30px]] i [[File:DPH16-Down.PNG|34px]] należy wybrać żądane konto. Na wyświetlaczu widoczne są jedynie konta, które zostały wprowadzone uprzednio w menu administratora.  
+
* Doorphone asks about selection of user account, which parameters you plan to change. Using navigation buttons [[File:DPH16-Up.PNG|30px]] and [[File:DPH16-Down.PNG|34px]] appropriate user account should be selected. Only accounts created previously in service menu are visible on display.  
−
Jedynie administrator ma możliwość tworzenia kont użytkowników. Po wybraniu konta użytkownika bramofon zażąda wprowadzeniu kodu PIN dla danego konta. Po raz pierwszy numer PIN konta użytkownika jest nadawany podczas tworzenia konta, na podstawie numeru tabeli kodów PIN określonego również w menu serwisowym. Administrator ma możliwość wygenerowania tabeli z nadanymi użytkownikom kodami PIN korzystając z generatora zawartego na stronie [http://keeper.slican.pl/servnet/generatory/gen_code_DPH.php Generator kodów BRAMOFON SLICAN DPH]. Użytkownik ma oczywiście możliwość zmiany przypisanego do jego konta kodu PIN za pomocą jednej z poniższych opcji. Opcje dostępne w menu użytkownika to:
+
Creating user account is only possible from service menu. After account selection doorphone asks about PIN code for selected account. First PIN code is assigned to user account during its creating, according PIN code table defined in service menu. Doorphone admin is authorized to generate PIN code table with PIN codes assigned to every specified account, using wizard on page [http://keeper.slican.pl/servnet/generatory/gen_code_DPH.php SLICAN DPH doorphone PIN code wizard]. Unfortunately this wizard is only in Polish. User can, of course, change assigned PIN code number, using one of below described option.
−
* Nowy PIN -  wybranie tej opcji pozwala na zmianę kodu PIN pozwalającego na wejście do menu użytkownika oraz wykonanie akcji identycznej jak wykonywana po naciśnięciu znaku * na telefonie, z którym zestawiona jest rozmowa z bramofonem (wysterowanie EZ, wysterowanie STA lub wysterowanie obydwu wyjść). Po wybraniu tej opcji bramofon poprosi o wprowadzeniu nowego kodu PIN. Po wprowadzeniu czwartej cyfry kodu PIN (kod musi posiadać cztery cyfry) konieczne jest ponowne wprowadzenie tego kodu. Jeżeli obydwa wprowadzone kody są identyczne, kod PIN zostanie zmieniony, co zostanie potwierdzone odpowiednim komunikatem na wyświetlaczu. Jeżeli wprowadzone kody nie są identyczne, na wyświetlaczu bramofonu pojawi się napis "Niezgodny PIN" i kod PIN nie zostanie zmieniony.
+
Options accessible in user menu are as follow:
−
* Nowa RFID - po wybraniu tej opcji bramofon poprosi o zbliżenie karty RFID i zarejestruje ją jako kartę użytkownika. Od tego momentu możliwe będzie wykonywanie akcji określonej jako "Akcja RFID", w wyniku przyłożenia do bramofonu tej karty.
+
* New PIN -  selecting this option enables to change PIN code, which enables to enter to user menu and to perform action defined in menu as "DTMF action" (trigerr EZ, trigerr STA or both output trigerr). After selecting this option doorphone asks for new PIN code entering. After entering fourth digit of PIN code (PIN code must consists of four digits) it is neccessarily to enter this code once more. If both entered PIN codes are identical, doorphone stores new PIN code, however if entered PIN codes are different user hears audio tone with low frequency and captioon "Mismatch PIN" appears on doorphone display.
−
* Usuń RFID - po wybraniu tej opcji, bramofon poprosi o potwierdzenie chęci usunięcia karty RFID. Po potwierdzeniu klawiszem [[File:DPH16-call.PNG|30px]], karta przypisana do konta danego użytkownika zostanie usunięta.
+
* New RFID - after selecting this option doorphone asks about approaching RFID card and registers this card as user card. From this moment it is possible to perform action defined as "RFID action" as a result of approaching this card to doorphone.
 +
* Remove RFID - After selecting this option doorphone asks about remove confirmation using button [[File:DPH16-call.PNG|30px]], after confirmation assigned card is removed.
 +
 
 +
{{References}}

Latest revision as of 05:37, 30 March 2021

DPH doorphone can be program with two methods:

  • From DTMF menu after establishing call between any phone and doorphone - remote programming
  • Using doorphone keyboard and display - local programming.

Using DTMF menu there is no possible to program all options, especially options which require reaction. Additionally local menu enables programming both admin and user options - user options are set by every user individually.

PIN code

Every DPH doorphone can be equipped in PIN code. By default there is no PIN code, PIN code can be used to protect DPH against unathorized access. You can define PIN code using DTMF code according table included in chapter concerning DTMF programing.

Warning! If you have no PIN code, it is possible to enter in DTMF menu only when SETUP jumper is inserted.


DPH16 - Programming using DTMF code

DTMFb menu structure in DPH doorphone is based on solution implemented in Slican PMS.

  • Entering to programming menu - during call digits 0987 should be dialed. [1]
  • All programming options are organized in XY array.
  • After pressing *, in every moment, entered parameter is canceled and program returns to XY coordinates selection.
  • After pressing # entered parameter is confirmed.
  • After pressing asterisk two times program mode is leaving.
  • After program mode leaving connection established for programming is disconnected
  • After dialing XY coordinates (programming option) confirmation (high frequency) or reject (low frequency) signal is generated.
  • Entering program mode is possible if jumper SETUP is ON.

After entering program mode:

  • All buttons are locked. Pressing any button generate rejection signal(low frquency).
  • DPH loudspeaker is muted.
  • Values in [ ] - default values.
Y/X 0 1 2 3 4 5 6 7 9 Parameter description


1 Short

number 0 [21]

Short

number 1 [none]

Numer

skrócony 2 [none]

Short

number 3 [none]

Short

number 4 [none]

Short

number 5 [none]

Short

number 6 [none]

Short

number 7 [none]

Short

number 9 [none]

Dialed no. Max 16 digits

No number - button off

2 Add # to number [1]

1 - on 0 - off

Only lifting handset [ ]

Short number, which only lifts handset

Values 0..9 None - any number

Max call time [180]

10..9000 sec

Finish call [0]

0 - none

1 - POD

2 - COD

3 - COD or POD

Default settings

'#' confirm Next DPH reset

Confirm. time [10] 0..60sec Call begin button [0]

0 - none

1 - POD

2 - COD

Short number 0 is dialed.

Auto answer [1]

0 - NO

1 - YES

Dialed numbers features
3 EZ opening time [3]

1..60 sek

EZ working mode [0]

0 - electrolock

1 - electromagnetic keeper

STA opening time [2]

1..360 sec

DTMF * receiving [3]

0 - no action

1 - EZ opening

2 - STA opening

3 - EZ and STA opening

RFID action [3]

0 - no action

1 - EZ opening

2 - STA opening

3 - EZ and STA opening

STA mode[0]

0 - Gate mode

1 - Light mode

SHK mode [0]

0 - SHK off
1- Button 1 - SHK
2- Button 2 - SHK
3- Button 1 and 2 - SHK

 EZ, STA parameters


4 Volume [3]

0..7

0 - min volume

Volume change

2 - increase volume

8 - decrease volume

For this option loudseaker is on

Microphone sensibility [1]

0 - low

1 - medium

2 - high

Switch level [2]

0..8 Minimal value of speak direction switching level

Acoustic signal parameters
5 Service RFID card

0000 - store service card

Service card enables to assign new user cards to user with number not assigned.


Remove RFID

0000- renove all user cards

x RFID cards
6 PIN change

Entering 4 digits PIN code Entering method: PPPP#PPPP#, P- any PIN digit 0..9, # - hash in DTMF

For sequence ## - erasing PIN (no PIN)

PIN entered in DTMF is equal to admin PIN entered from DPH16 keyboard.

PIN


  • XY coordinates acceptation causes high frquency (OK) signal generation.
  • It is possible to entering XY coordinates longer than 2 digits - only two last digits will be used.
  • XY coordinates confirmation - button HASH (#)
  • Parameter entering can be always canceled by STAR (*) button. as a result low frequency signal (BAD) is generated and jump to coordinates selecting
  • Confirmation of any parameter can be done with HASH (#) button. If parameter value is correct and parameterr was succesfully stored in FLASH memory - high frequency signal (OK) is generated and dorphone waits for coordinates selection.
  • If parameter value is incorrect - low frequency signal (BAD) is generated and dorphone waits for coordinates selection.
  • Max call time - new value is obvious for next call
  • Autoconfirmation time - time needed to automatic confirmation entered number. If 0, after 20 seconds entered number will be canceled.
  • Parameter Switch level operating in following manner: phone signal strenght must be proportional to value of this parameter to be hear in doorphone speaker. Change of this parameter is helpful for calls quality if noise generated in phone premise is very high. While to low swithing level voice from doorphone can be interrupted. Configuration range is between 0 and 8, default value is equal to 2. Correct value should be set according experiment, individually fot every doorphone location.
  • If value of STA mode option is equal to 0, active are STA control by RFID, PINu and DTMF, otherwise if value of STA mode option is set to 1, only only pressing any button or answering incoming call can trigger STA output.
  • If value of option Auto answer is equal to 0, an incoming call can't be answered by doorphone. In this situation, doorphone DTMF programming is possible only after establishing call from doorphone to phone.

DPH16 - Service menu maintenance

Due to display installed in DPH.AB-KS16 doorphone as well as installed numeric keyboard includes navigation keys, it is possible to program doorphone functionality directly from keyboard without using DTMF code described above.

Warning! Because DPH doorphone maintenance is provided using touch keyboard, every pressing button is confirmed by audio signal.

From doorphone menu is possible to program all options, available from phone using DTMF codes and options, which cannot be programmed from phone keyboard using DTMF codes (or it is very difficult to realize). During service menu option description it is clearly defined, which options are accessible using DTMF menu. Entering service menu takes place as follow:

  • Press two times DPH16-Kluczyk.PNG button.
  • With navigation buttons- DPH16-Up.PNG and DPH16-Down.PNG select "Service" menu.
  • Confirm selection by pressing DPH16-call.PNG button.
  • Doorphone asks about PIN code. By default there is no PIN code, to enter this menu. To enter service menu you can insert SETUP jumper[2]. If PIN code is defined, after entering 4th digit - if entered PIN code is correct - on doorphone first option of first menu level is displayed. All menu levels and options on every menu level are presented in this chapter, in paragraph about menu structure. While entering wrong PIN, signal coonfirming entering last character is generated, but frequency of this signal is different (lower) than nolmally.

DPH16 - Menu structure

As mentioned in previous paragraph, after entering proper PIN code, on doorphone display firsyt option of first menu level is visible - here is option "Names". Using buttons DPH16-Up.PNG and DPH16-Down.PNG you can navigate between options of specified menu level. Specified option can be selected by pressing DPH16-call.PNG button, next menu level is displayed (according below figure) or selected option can be edited (if this option is not assigned to any next menu level). After pressing button DPH16-end.PNG previous level menu is selected or edition mode canceled without saving entered data. If you press button DPH16-C.PNG during edition of specified option, last entered character will be erased.

Following figure presents doorphone menu structure with all options on every menu level. DPHMenuSevice1.25.png
Names - this option is used to define up to 50 names, to which numbers (internal or external) dialed by doorphone after selecting specified name are assigned.

  • Screen text - editable text, which will be displayd on screen in idle status.
    • text is displayed on screen in place od short number,
    • no possibility to make a call on idle screen (to make a call it is necessary to search a short number using 30px or 30px keys, and then press 30px),
    • below the screen text, there is "Search" text displayed, but only if there is at least one short number on the list and "search" text displaying is turned on (Setting -> Show "Search").

Maximum lenght of the text is 64 digits. Text is centered in default, but it can be aligned to the left or right by putting \l or \r letter in front of the text. Text can be enforced to the next line by typig /n before the text.

  • Name 0 .. Name 49 - After selecting one ot these options you can enter any name (including maximally 20 characters), after selecting this name, doorphone dials number assibned to this name. If you press button DPH16-call.PNG, when specified name is on display, edition of this name is started.

Number - this option is used to define numbers dialed by doorphone after selecting Name 0...Name 9.

    • Number 0 .. Number 49 - after selecting one of these options you can enter any number(including maximally 16 digits), this number will be dialed by doorphone if you select appropriate Name 0 - ...9, Number 0 is assigned to Name 0 etc.
  • Hot line - selecting this option enables to define hot line as as one of numbers. Ex. if in edition mode number 2 was defined as hot line, after selecting Name 2 from doorphone keyboard, only simulation of lifting handset will be performed, number defined as Number 2 will not be dialed. It should be remembered, that numer name defined as hot line must be defined. If this number is not defined, there is not possible to select name defined as hot line.

Settings - this option enables to set several doorphone parameters

  • Dialing time - this parameter defines time in seconds, after this time number entered from keyboard is dialed by doorphone, even if entering number is not confirmed by pressing DPH16-call.PNG button. By default this time is set to 10s.
  • Call time - this option enebles to set maximal time of call established between doorphone and any phone. By default this time is set to 180s. It should be noticed, that doorphone is equipped in busy signal detector and call is automatically disconnected after hanging off handset of phone connected to doorphone.
  • Add # - this option enables to add # after number dialed by doorphone. It is important if PBX works in slow number analisys mode andafter entering last number digit PBX waits for time of slow number analisys, before dialing this number. Character # added on number end eliminates this time.
  • Only short No. - when this option is turned on, only short numbers are available to dial. First 10 numbers are accessible from keypad keys, and rest rest can be searched with 30px and 30px keys.
  • Auto Answer - all incoming calls will be automatically answered.
  • Show "Search" - turning option off will erase search text from screen. Recommended, when screen text is longer than 3 lines.
  • EZ time - this option enables to set the time (in seconds) of opening electrolock connected to doorphone, this time defines how long the electrolock is open after sending 1, or * sign (if EZ openinig was defined as "DTMF action"). By default this time is equal to 3s.
  • EZ mode - this option enables to set electrolock working mode. Two different working mode are possible:
    • Electrolock - for this option, during the time defined as "EZ time" parameter, 12V voltage is connected to electrolock terminals.
    • Electromagnetic keeper - for this option, 12V voltage is connected continously to electrolock terminals, however after opening door by the time defined by "EZ time" parameter, this voltage is not connected to electrolock terminals.
  • STA time - this option enables to set time (in seconds) of trigger additional relay connected to doorphone, after sending character 2 or * (if trigger this relay is defined as "DTMF action"). By default this time is set to 2s.
  • STA mode - this option define type of device connected to STA output. If value of STA mode option is equal to 0, STA output is trigged by RFID, PINu and DTMF, otherwise if value of STA mode option is set to 1, only pressing any button or answering incoming call can trigger STA output.
  • Test EZ&STA - it is typical service option, it tests if doorphone trigerr EZ and STA outputs. After selecting this option, menu including three followiung options is displayed on doorphone display:
    • EZ output - after selecting this option an output with electrolock connected to is triggered
    • STA output - after selecting this option an output with additional relay STA connected is trigerred
    • EZ&STA output - after selecting this option outputs EZ and STA are trigerred in the same time
  • DTMF action - this option enables to define type of action performed after sending * to doorphone. After selecting this option, menu including four following options is displayed on doorphone display:
    • None - no action is performed after sending * to doorphone
    • EZ open - after sending * to doorphone EZ output is trigerred
    • STA open - after sending * to doorphone STA output is trigerred
    • EZ&STA open - after sending * to doorphone EZ and STA output are trigerred
  • RFID action - othis option enables to define type of action performed after approach of registered RFID card. After selecting this option, menu including four following options is displayed on doorphone display:
    • None- no action is performed after approach of registered RFID card
    • EZ open - after approach of registered RFID card EZ ootput is trigerred
    • STA oopen - after approach of registered RFID card EZ and STA ootput are trigerred
    • EZ&STA open - after approach of registered RFID card STA ootput is trigerred
  • Call end - this option enables to finish call as a result of local action, no matter what is a status of phone connected with doorphone. After selecting this option, menu including four following options is displayed on doorphone display:
    • None - connection with doorphone will be finished only after hang off the handset of the phone connected to doorphone or after time defined by "Call time" parameter.
    • POD - connection with doorphone will be finished after hang off the handset of the phone connected to doorphone or after time defined by "Call time" parameter or after pressing POD button.
    • COD - connection with doorphone will be finished after hang off the handset of the phone connected to doorphone or after time defined by "Call time" parameter or after COD sensor triger.
    • POD or COD - connection with doorphone will be finished after hang off the handset of the phone connected to doorphone or after time defined by "Call time" parameter, after pressing POD button or after COD sensor triger.
  • Language - after selecting this option it is possible to set language of communication between doorphone and user. Possible is Polish and English language.
  • LCD contrast - selecting this option enables to set contrast of LCD display, in 11-stage scale. By default 6 stage is set.
  • Factory settings - selecting this option enables to restore doorphone factory settings. Before restore factory settings, doorphone ask about selection confirmation.
  • About - selecting this option enables to present version of software uploaded to doorphone, this software creation date and author info.

Acoustic - this option is used to doorphone acoustic parameter set.

  • SPK volume - this option is used to set doorphone speaker volume in 7-stage scale. By default 3 stage is set.
  • MIC sens - othis option is used to set doorphone microphone sensitivity in tri stage scale Low, Medium, High. By default Medium sensitivity is set.

Accounts - selecting this option enables to create and erase user accounts and display parameters set for this accounts. After selecting this option, menu including following options is displayed on doorphone display:

  • Show - after selecting this option, caption "Account number" and number of already created account are displayed on doorphone display. Such display status is about 2 seconds and then first of registered accounts as well as context menu "Option" and "Exit" are displayed on doorphone display. After press button DPH16-end.PNG you go back to menu "Accounts", while after press button DPH16-call.PNG next menu appears on display. It includes following options:
    • New PIN - this option enables to change user PIN code. After selecting this option, doorphone asks to enter new PIN code and next after its confirmation using button DPH16-call.PNG, asks about once more entering new PIN code. After second entering, if both entered PIN codes are identical, doorphone stores ne PIN code, however if entered PIN codes are different user hears audio tone with low frequency and captioon "Mismatch PIN" appears on doorphone display
    • New RFID - this option enables to assign new RFID card to user account, using this card it is possible to perform action defined as "RFID action". After selecting this option doorphone asks about approaching RFID card.
      Attention! Card registered in doorphone should have the unique ID, so it is impossible to assign the same card to two different user accounts. Symilarly it is not possible to register two different cards to one user account. Card assigned as second replaces earlier assigned card.
    • Remove RFID - this option enables to remove already assigned RFID card. After selecting this option doorphone asks about remove confirmation using button DPH16-call.PNG, after confirmation assigned card is removed. Pressing button DPH16-end.PNG returns to option "Remove RFID" without removing bez usuwania istniejącego przypisania.
    • Delete account - this option enables to delete specified user account with all data assigned to this account. After selecting this option doorphone asks about delete confirmation using button DPH16-call.PNG, after confirmation specified account is deleted. Pressing button DPH16-end.PNG returns to option "Delete account" without deleting account.
    • Add account - this option enables to add an account, if account is not registered yet. Method of naming accounts defined in doorphone DPH.AB-KS16 is strictly determined. Account name consists always with caption "Account" and number from range 1..9999, including always four digits. Total number of accounts defined in doorphone cannot increase above 512. After selecting this option doorphone suggests number one more than higher created number. User who add new account can of course change proposed number (world "Account" cannot be changed), but if account with entered number already exists, doorphone informs about it. If account with highest possible number (9999) already exists, doorphone proposes to create an account with highest free number. After eventually change of proposed by doorphone number, new account should be created by pressing button DPH16-call.PNG. Doorphone informs about creating account with message "Account xxxx created" where xxxx is number of created account. If account with entered number already exists, doorphone informs about it with message "Entered acc. exists". If number of defined accounts is beyond 512, caption "To many acc".
    • Add - this option enables to create new account. Rules of creating new accounts are the same as in above point.
    • Delete - this option enables to delete wrongly entered or unused account. After selecting this option, list of accounts is displayed on doorphone display. They can be selected with buttons DPH16-Up.PNG and DPH16-Down.PNG, after selecting account to delete, press button DPH16-call.PNG, it deletes specified account with confirmation message "Account xxxx deleted".
    • PIN table No - while adding new account as described above, doorphone generates four digits PIN code for every account, this PIN code is used to opening door and to enter in user menu. PIN code is generated according table of PIN codes, this option is used to determine this number. It is possible to generate some PIN codes according one PIN table number, and another part of numbers can be generated according another PIN table number. Table number is always four digits, if user with this option enter less than four digits, doorphon automatically adds appropriate number of digit 0 at the begining of entered number. By default this number is equal to 1234.
    • Generate - this option enables to genetrate more than one account and assigning PIN codes to these accounts.

Service - this option enables to change parameters, which enable to enter into service menu. After selecting this option, menu including three following options is displayed on doorphone display:

  • Change PIN - selecting this option enables to change PIN code, which enables enter to service menu. After selecting this option doorphone asks about entering new PIN code. After entering fourth digit of PIN code (PIN code must consists of four digits) it is necessarily to entering this code once more. If both entered codes are identical, PIN code will b e changed, it is confirmed by appropriate message on doorphone display, however if entered PIN codes are different user hears audio tone with low frequency and caption "Mismatch PIN" appears on doorphone display
  • Set RFID - after selecting this option doorphone asks about approaching RFID card and registers it as service cerd. From this moment it is possible to entering into service menu as a result of approaching this card to doorphoe without entering service PIN code.
  • Del RFID - after selecting this option doorphone asks about confirmation of deleting RFID card. After confirmation with button DPH16-call.PNG, registered card is deleted.

DPH16 - User menu maintenance

Etering into user menu can be done as follows:

  • Press two times button DPH16-Kluczyk.PNG.
  • With navigation keys DPH16-Up.PNG and DPH16-Down.PNG select option "USER".
  • Confirm selection by pressing button DPH16-call.PNG.
  • Doorphone asks about selection of user account, which parameters you plan to change. Using navigation buttons DPH16-Up.PNG and DPH16-Down.PNG appropriate user account should be selected. Only accounts created previously in service menu are visible on display.

Creating user account is only possible from service menu. After account selection doorphone asks about PIN code for selected account. First PIN code is assigned to user account during its creating, according PIN code table defined in service menu. Doorphone admin is authorized to generate PIN code table with PIN codes assigned to every specified account, using wizard on page SLICAN DPH doorphone PIN code wizard. Unfortunately this wizard is only in Polish. User can, of course, change assigned PIN code number, using one of below described option. Options accessible in user menu are as follow:

  • New PIN - selecting this option enables to change PIN code, which enables to enter to user menu and to perform action defined in menu as "DTMF action" (trigerr EZ, trigerr STA or both output trigerr). After selecting this option doorphone asks for new PIN code entering. After entering fourth digit of PIN code (PIN code must consists of four digits) it is neccessarily to enter this code once more. If both entered PIN codes are identical, doorphone stores new PIN code, however if entered PIN codes are different user hears audio tone with low frequency and captioon "Mismatch PIN" appears on doorphone display.
  • New RFID - after selecting this option doorphone asks about approaching RFID card and registers this card as user card. From this moment it is possible to perform action defined as "RFID action" as a result of approaching this card to doorphone.
  • Remove RFID - After selecting this option doorphone asks about remove confirmation using button DPH16-call.PNG, after confirmation assigned card is removed.

References

  1. ↑ If there is no PIN code defined, there is no possibility to enter in DTMF nenu.
  2. ↑ If SETUP jumper is inserted and there is no PIN code defined, DPH.AB-KS16 is always in service menu and there is no possibility to normal DPH operation.
Retrieved from "https://pubwiki.slican.com/index.php?title=DPH_-_Doorphone_DPH.AB-KS16_programming&oldid=7946"