DPH - Doorphone programming

Establishing call

• To program DPH doorphone it is necessarily to establish call between PBX phone and doorphone.
• Doorphone is programmed using DTMF tones send by phone connected to doorphone.

Programing mode entering: 0987

• To enter programing mode - during established call dial: 0987
• In programing mode:
  • doorphone buttons don't operate and after pressing any button reject signal (low frequency) is generated.
  • Loudspeaker is muted.

Navigation

*(asterisk) Cancel

• After pressing *, in every moment, entered parameter is canceled and program returns to XY coordinates selection.

# (hash)OK Confirm

• After pressing # entered parameter is confirmed.
• After pressing # doorphone answers as follows:
  • confirmation signal (high frequency)
  • rejest signal (low frequency) if entered parameter is improper.

Leaving programing mode 2 x * (asterisk)

• After pressing asterisk two times program mode is leaving.

Warning! Entering program mode is possible if jumper SETUP is ON.

Programming table

• Values in [ ] - default values
• All programmable fields are organized as XY coordinates table.

DPH programming table is as follow

Y\X	0	1	2	3	4	Meaning
1	Short number 0 Top button [21]	Short number 1 Bottom button [empty]				Number dialed after pressing button. Max 16 digits No number - button disabled
2	Number dialing finish with #(Hash) [1] 1 - ON 0 - OFF	Only handset lifting [ ] Line occupation. In PBX hot line must be declared. 0-Top button 1-Bottom button Empty - hot line is inactive	Max call time [180] 10..360 sec	Not operated	DPH factory settings # confirm, after confirmation DPH resets	Settings
3	EZ opening time [3] 1..60 sec	EZ working mode [0] 0 - electrolock (NO) 1 - electromagnetic keeper (NC)	STA opening time [2] 1..60 sec	Receiving DTMF * [3] 0 - no action 1 - EZ opening 2 - STA opening 3 - EZ and STA opening at the same time	User RFID action [3] 0 - no action 1 - EZ opening 2 - STA opening 3 - EZ and STA opening at the same time	Output settings EZ - electrolock, STA - automatic control
4	Speaker volume [3] Allowable values 0..7, 0 - minimal volume	Speaker volume change 2 - increase volume 8 - decrease volume During adjustment DPH speaker is active	Speaker sensitivity [1] 0 - small 1 - medium 2 - high			Acoustic settings
5	Service RFID card 0000 - store service card Service card enables to assign new RFID cards.	Remove RFID cards 0000- remove all RFID cards				RFID cards
6	Zmiana PIN Wprowadzenie 4 cyfrowego numeru PIN Sposób wprowadzenia: PPPP#PPPP#, P- dowolna cyfra 0..9 PINu, # - hash w DTMF Gdy podana sekwencja ## - usunięcie PIN (brak PIN) PIN w DTMF jest równy PIN administratora wprowadzony z klawiatury DPH16.					===PIN===|} Summary XY coordinates acceptation causes high frquency (OK) signal generation. It is possible to entering XY coordinates longer than 2 digits - only two last digits will be used. XY coordinates confirmation - button HASH (#) Parameter entering can be always canceled by STAR (*) button. as a result low frequency signal (BAD) is generated and jump to coordinates selecting Confirmation of any parameter can be done with HASH (#) button. If parameter value is correct and parameterr was succesfully stored in FLASH memory - high frequency signal (OK) is generated and dorphone waits for coordinates selection. If parameter value is incorrect - low frequency signal (BAD) is generated and dorphone waits for coordinates selection. Max call time - new value is obvious for next call For DPH.AB-KS1 short number 0 is active For DPH.AB-KS2 short numbers 0 (upper button) and 1 (lower button) are active For DPH.AB-KS1, 2RF field 05 is active (RFID cards) Back