DPH - Doorphone programming
Establishing call
- To program DPH doorphone it is necessarily to establish call between PBX phone and doorphone.
- Doorphone is programmed using DTMF tones send by phone connected to doorphone.
Programing mode entering: 0987
- To enter programing mode - during established call dial: 0987
- In programing mode:
- doorphone buttons don't operate and after pressing any button reject signal (low frequency) is generated.
- Loudspeaker is muted.
*(asterisk) Cancel
- After pressing *, in every moment, entered parameter is canceled and program returns to XY coordinates selection.
# (hash)OK Confirm
- After pressing # entered parameter is confirmed.
- After pressing # doorphone answers as follows:
- confirmation signal (high frequency)
- rejest signal (low frequency) if entered parameter is improper.
Leaving programing mode 2 x * (asterisk)
- After pressing asterisk two times program mode is leaving.
|
Programming table
- Values in [ ] - default values
- All programmable fields are organized as XY coordinates table.
DPH programming table is as follow
| Y\X | 0 | 1 | 2 | 3 | 4 | Meaning |
|---|---|---|---|---|---|---|
| 1 | Short number 0 Top button [21] |
Short number 1 Bottom button [empty] |
Number dialed after pressing button.Max 16 digits No number - button disabled | |||
| 2 | Number dialing finish with #(Hash) [1] 1 - ON 0 - OFF |
Only handset lifting [ ]
Line occupation. In PBX hot line must be declared. |
Max call time [180]
10..360 sec |
Not operated | DPH factory settings
# confirm, after confirmation DPH resets |
Settings |
| 3 | EZ opening time [3] 1..60 sec | EZ working mode [0]
0 - electrolock (NO) |
STA opening time [2]
1..60 sec |
Receiving DTMF * [3]
0 - no action |
User RFID action [3]
0 - no action |
Output settings
|
| 4 | Speaker volume [3] Allowable values 0..7, 0 - minimal volume |
Speaker volume change 2 - increase volume 8 - decrease volume During adjustment DPH speaker is active |
Speaker sensitivity [1]
0 - small |
Acoustic settings | ||
| 5 | Service RFID card 0000 - store service card Service card enables to assign new RFID cards. |
Remove RFID cards 0000- remove all RFID cards |
RFID cards | |||
| 6 | Zmiana PIN
Wprowadzenie 4 cyfrowego numeru PIN Sposób wprowadzenia: PPPP#PPPP#, P- dowolna cyfra 0..9 PINu, # - hash w DTMF Gdy podana sekwencja ## - usunięcie PIN (brak PIN) PIN w DTMF jest równy PIN administratora wprowadzony z klawiatury DPH16. |
PIN |
Summary
- XY coordinates acceptation causes high frquency (OK) signal generation.
- It is possible to entering XY coordinates longer than 2 digits - only two last digits will be used.
- XY coordinates confirmation - button HASH (#)
- Parameter entering can be always canceled by STAR (*) button. as a result low frequency signal (BAD) is generated and jump to coordinates selecting
- Confirmation of any parameter can be done with HASH (#) button. If parameter value is correct and parameterr was succesfully stored in FLASH memory - high frequency signal (OK) is generated and dorphone waits for coordinates selection.
- If parameter value is incorrect - low frequency signal (BAD) is generated and dorphone waits for coordinates selection.
- Max call time - new value is obvious for next call
- For DPH.AB-KS1 short number 0 is active
- For DPH.AB-KS2 short numbers 0 (upper button) and 1 (lower button) are active
- For DPH.AB-KS1, 2RF field 05 is active (RFID cards)
