Instrukcja obsługi IPS/IPS manual

	Numerical keys in a phone with tone dialling
	Extra keys
	Any key from 0..9
	Four-digit user's or ACD group's PIN
	Old PIN
	New PIN
	Giving time for some services (e.g. alarm clock) HH - hour (00..23), MM - minutes (00..59)
	Catalogue number of a PBX subscriber for which the service is being activated
	Account number
	Number of PBX work mode (range 1..8)
	FLASH button
	Subscriber's number in an ACD group
	ACD group number - ID number and not a catalogue number
	Dialling any catalogue number (extension) or an outgoing number
	Lifting the handset or activating the 'Hands Free' mode in the telephone
	Hanging up the handset or deactivating the 'Hands Free' mode in the telephone
	The service is selected during an active call

Completing services in IPx PBXes

Dialling a number (calling)

	Lift the handset.
	Dial a number after you hear the PBX dialling tone.
	Wait for the connection and start conversation.
	Hang up the handset after the conversation.

Selecting a service

	Lift the handset.
	Tone dial a service after you hear the PBX dialling tone.
	Wait for the PBX message that acknowledges acceptance of service.
	Hang up the handset.

Selecting a service during an active call

	Lift the handset.
	Dial a number after you hear the PBX dialling tone.
	During an active call press the FLASH button on the phone.
	Tone dial a service after you hear the PBX dialling tone.
	Wait for the PBX message that acknowledges acceptance of service.
	Hang up the handset.

Operation on voice announcements

Recording a voice announcement using a phone (#92)

	Lift the handset.
	Dial the code for the Record/Play the announcement function.
	Enter the four digit pass code for recording (playing).
	Enter the announcement number (1..9).
	If the anouncement is already recorded, the PBX will play the announcement. To listen again, press *. If there is no announcement to play, the service dialing tone will be heard. Press # to start recording.
	Record the announcement.
	When the announcement is finished, press any numerical key to finish.
	Play the recorded announcement. To change it, press # again and record new announcement.
	Hang up the handset.

Warning: Voice announcements can be recorded only by a subscriber with appropriate authorization assigned by admin.

The service is also available after logging in to DISA account.

Deleting a voice announcement using a phone (#92)

	Lift the handset.
	Dial the code for the Record/Play the announcement function.
	Enter the four digit pass code for recording (playing).
	Enter the announcement number (1..9).
	The recorded announcement will be played. Press 0 after listening to delete the announcement.
	Hang up the handset.

Warning: Voice announcements can be deleted only by a subscriber with appropriate authorization assigned by admin.

The service is also available after logging in to the DISA account.

Recording and setting private DND message (#79)

A DND message is one of the DISA/information line announcements marked in the system as 1 to 9 or a private message up to 30seconds long recorded individually by the subscriber with the authorization for it assigned by the PBX admin. Such an announcement will be played to the person calling the PBX's subscriber when the DND function is activated (do not disturb) or routed to the voice mail in the subscriber's phone.

Checking status/deactivating the DND message function

	Lift the handset.
	Select the function code.
	Pressing * checks the status, i.e. shows if the DND message is activated or not.

If the service is activated, then:

• with DND activated in the subscriber's phone, the person calling the subscriber will hear the private DND message
  

or one of the DISA/information line announcements,

• with voice mail activated at the subscriber's side, the call originator will hear the DND private message or one of the
  

DISA/information line announcements, and then a sound will be played to signal the beginning of recording.
So it is a good idea to include information for the call originator that they can leave a message after the beep
in the DND message.

If the service is inactive, then:

• With DND activated the person calling the subscriber on the extension will hear The subscriber is currently unavailable,
  

please call again later, and the person calling from the city network will receive the busy signal,

• with voice mail activated the call originator will hear You have reached voice mail, leave message after the beep.

Pressing the key again will deactivate the service.

Recording a private DND message

	Lift the handset.
	Select the function code.
	Pressing # starts recording of a DND private message.
	Record the message. Press any numerical key or hang up the handset when recording is finished. Maximum time of recording for an announcement is 30seconds.
	Press * to listen to the recorded announcement.
	Press 0 to delete the recorded announcement and deactivate the service.
	Pressing # will start the recording of a DND private message again.

Setting the selected announcement as a DND message

	Lift the handset.
	Select the function code.
.....	Selecting a digit from 0 to 9 plays an announcement: 0 the private DND message recorded by the subscriber, 1..9 one of the DISA/information line announcements.
.....	Selecting a digit from 0 to 9 again will play another or the same announcement.
	Selecting during or after the playback of the announcement selects this announcement as a DND message. Alternate pressing of * will turn on/off the service.

Warning: Owing to hardware limitations only one person at a time can use the message recording function. In the case of a recording attempt when the recording channel is busy, the subscriber will receive the busy signal.

Transferring calls between subscribers

	During a received call.
	Press the FLASH key on the telephone.
	After hearing the PBX dialling tone, dial the number of the subscriber you want to transfer the call to.
	If you are transferring a call with offering, wait for the subscriber's answer.
	Hang up the handset.

WARNING: To transfer a call to an external number (transit connection), you need appropriate rights assigned by the PBX service.

WARNING: During the set up of a transit connection at least one of translations must be a digital translation (ISDN, GSM or VoIP).

Conferences and three-party (3PTY) calls

Conference call

Individual setting up of a conference call, selecting participants, giving floor, private conversations in a conference are possible only for users of Slican system phones CTS-202; Slican CTS-102.CL and Slican CTS-102.IP. Setting up such connections and their management are described in detail in the operation manuals of these phones, which can be read HERE

It is possible to set up only conference calls prepared previously by the system admin and saved in the phone as a conference group using an analogue phone in PBXes by Slican. A subscriber with appropriate rights sets up such a connection in the following way:

After selecting the group number, the phones programmed by the admin start ringing and after lifting the handset their users will hear the message "Teleconference" and will then be connected to the conversation in a conference group.
It is not possible to add anyone after setting up a conference and the conference cannot be transferred to other users. Hanging up the handset by the conference originator ends the conference.

Conference room

The operation of a Conference room is opposite to the Conference group. This function is intended for previously arranged conference calls with the participants calling a specified number and joining the conference by themselves. The number for the Conference room must be defined first by the PBX admin. Depending on the configuration, the Conference room can be available only in the internal network or also in the external network. The PBX admin can define specific numbers, both extensions and outgoing numbers that are allowed to immediately join the Conference room. The person calling the Conference room from an undefined number or unlisted number can enter the room by entering a PIN. They will not be able to join the Conference room if a PIN was not defined by the system admin. If the number is defined for the Conference room and the call is made within an internal network, the calling method is as follows:

If the number is NOT defined in the Conference room and the call is made within the internal network, the call is made using the following method:

If the group is available for the external connections, then the PBX admin will provide the outgoing number to be called to get access to the Conference room.
The Conference room may have its host which should be equipped with a Slican system phoneCTS-202; Slican CTS-102.CL and Slican CTS-102.IP. They can manage a conference according to the rules described HERE

Three-party call (Flash #3)

	AbA subscriber calls AbB.
	During the conversation any of the AbA or AbB subscribers presses the FLASH key on the phone.
	Dial the AbC subscriber's number after you hear the PBX dialling tone.
	Press the FLASH key during an active connection, and then #3 on the telephone.
	A connection between the subscribers AbA, AbB and AbC was set up.

Functions available to the subscriber setting up the three-party call during an active call:

• - Finishing the connection and disconnecting all participants.
• - Conversation with the first participant of the connection. The second of the connected participants hears music
• - Conversation with the second participant of the connection. The first participant hears music

Description of services

General notes for the operation of services

• Interruption of power supply does not result in the deletion of the installed services.
• Most of the services can be installed by the PBX admin in ConfigMAN.
• CCT-1668 PBX inform about the acceptance or rejection of a service by word messages.
• A PIN must include four digits from 0..9.
• Availability of services depends on the rights assigned by the PBX admin.

Warning:

The services described in the manual apply to analogue and ISDN phones.

Warning:

The description of the services in system phones is given in the Operations and Maintenance Manual of system phones Slican CTS-202.CL, CTS-202.Plus and CTS-202.IP.

Phone locking services

Phone locking (#21)

Description of service
"Phone Locking" means that your phone has got the lowest level rights. This service is active until its deactivation in the phone. Using a locked phone you can call a temporary account. The service is active only in the telephone and not on the called account.

The service is also available after logging in to a DISA account.
Entering the wrong PIN code three times locks the services. Unlocking is possible using the service #999

Phone lock test

Checking if the Phone locking function is activated on the phone.

Unlocking the phone (#20)

How to select

Description of service
Cancelling the phone locking. Cancelling the lock can be impossible if the automatic locking of the phone after the set time is activated in the PBX.
Entering the wrong PIN code three times locks the services. Unlocking is possible using the service #999

Do not disturb - DND (#22)

Description of service Operation of the Do not disturb service:

• If the call originator selects a direct number of a subscriber with active DND service, the originator will receive the message: "Subscriber unavailable now."
• If the call originator selects a group number, the subscriber who has activated the DND service and who belongs to this group will be treated as a busy subscriber.

The service is also available after logging in to a DISA account.

Activating the DND service

How to select

Deactivating the DND service

How to select

Testing the do not disturb DND service

How to select

Checking if the DND service is activated on the phone.

IMPORTANT!

If an AbA subscriber has activated the DND service, then there is a situation when the AbB subscriber calling such AbA subscriber will nevertheless reach this subscriber. To make this possible, the AbB calling subscriber must have VIP rights assigned by the PBX admin and must also use the #25 service Urgent call before dialling the number.

Services associated with location

Park - HOLD (#31)

How to select Description of service

• If an AbA subscriber activates the park function during the conversation with an AbB subscriber, then the AbB will be parked for 3minutes and hear music in their handset.
• After hearing the message Service accepted, subscriberA hangs up the handset (uses this service instead of pressing the HOLD button on the phone) or hangs up the phone, and then picks it up to set up another connection (i.e. wants to consult with another agent).
• If the AbA subscriber selects #31 without other subscriber parked, then they will come back to the conversation with AbB.
• This service enables parking only one subscriber. If the AbA subscriber does not unpark the AbB subscriber (by selecting #31) during 3minutes from the time of activating the parking service, then the parked AbB subscriber will send a reminder made of a series of short rings at the AbA's phone.
• It is possible to unpark the AbB subscriber on another phone.

Remote recovering of a forwarded call (#32)

Interception of a forwarded call

Unparking a call How to select
Description of service
The service recovers the last parked connection on a different telephone to the one used for calling the park function #31. Also this service is used for intercepting a forwarded call provided it has not been completed. If the calls are transferred to another phone (e.g. a cell phone), then it is possible to use any phone and select the service #32 and the number of telephone performing the transfer at the time of transferring. The forwarded call will be recovered at this moment.

Intercepting a call from subscriber cancelling a transfer (#36)

How to select
Description of service
This service intercepts a call from the selected phone or recovering a transferred call that has not been completed yet (not answered yet). This service will not be completed when the subscriber that the call was transferred to answered the call or when the subscriber originating the call stopped the call.

Move back forwarding to the previous subscriber (#39)

Undo forwarding to the previous subscriber
How to select

Description of service It is possible to move back the call that was forwarded to you to the person that forwarded it. If the service of moving back to the person transferring is unsuccessful, then the call will be returned to you.

Services in the PickUp Group (call interception group)

Calling your PickUp group (#34)

Urgent call in a PickUp Group
How to select

Description of service:
Selecting this sequence enables immediate calling your Pickup group. A PBX can complete only one call of this type at a time.

Urgent call in a PickUp group (#35)

Urgent call in a PickUp Group
How to select

Description of service:
If there is a system phone at the AbB subscriber side, then you will gain access to their speaker. If the subscriber uses an analogue phone, then a special ringer is activated. This service is active for the duration of the call. The availability of this service depends on the rights assigned to the specific subscriber by the PBX admin.

The service is also available after logging in to a DISA account.

Call interception in a PickUp group (#37)

Call interception in a PickUp Group
How to select

Description of service:
Intercepting calls from subscribers from the same PickUp group (call interception group).

Services in an ACD group

Logging a subscriber by the group's coach (#59)

Logging a subscriber to an ACD group

How to select
|
Description of service:
The group coach can use this service to log in a subscriber to an ACD group. Calls for this subscriber will be forwarded according to the group settings.

If the group does not have a PIN assigned, then the logging of a subscriber in and out of the group will be possible only by the group's coach.

Logging a subscriber off an ACD group

How to select

Description of service:
The service enables the group's coach to log off a subscriber from an ACD group.

Logging in to an ACD group (#58)

Logging in to an ACD group

How to select

Description of service:
This service enables any subscriber to log in to an ACD group. After logging in, the calls to this subscriber will be forwarded according to the group settings. If the group does not have a PIN assigned, then logging a subscriber in and off the group is possible only by the group's coach. A subscriber with the active Do not disturb - DND (#22) service cannot log in to the group. If they try to log in, pressing the sequence #58 will result in the message Service unavailable.

Logging off from an ACD group

How to select

Description of service:
This service enables a member of an ACD group to log off from it.

Services associated with accounts

Checking the amount available for calls (#51)

How to select

Description of service
Possibility to check the available limit amount (if such limits are activated on the phone). The subscriber will hear the Service accepted message after selecting the service. After hanging up the handset, a single ring will be heard and the numerical display will show the phone or account number, and the alphanumeric display will show Amount: xx.xx. If the amount available for use is lower than 50grosz (call locking), the following message will be displayed instead of the amount: Amount: - - -.

This service is available when the Phone locking service is not active, the subscriber has an active limit and the analogue phone enables the number presentation.

Temporary calling an account (#52)

How to select

Description of service:
The rights for a telephone of account rights can be called up on any telephone in a PBX. The call being performed is accounted for the account owner and the number presentation complies with the settings of the installed account. The account being temporarily called is automatically called off after 5seconds from the moment of hanging up the handset. The account can be also called from outside using a trunk by DISA and using this function to make transit calls using their subscriber account. This requires correct subscriber's rights assigned by the PBX admin.

The service is also available after logging in to a DISA account.
Entering the wrong PIN code three times locks the services. Unlocking is possible using the service #999

Calling the account permanently (#53)

How to select

Description of service:
The rights for a telephone of account rights can be called up on any telephone in a PBX. The call being performed is accounted for the account owner and the call presentation complies with the settings of the installed account. This will result in the immediate forwarding of calls to the phone where the #53 service is active. A fixed account can also be called on a locked phone. Entering the wrong PIN code three times locks the services. Unlocking is possible using the service #999

Cancelling the account called permanently

How to select

Description of service:
An account that has been called permanently can be cancelled by calling the function #53# or by registering it on another phone. A fixed account that is not be cancelled, will be cancelled automatically after the period defined by the PBX admin. Calling the account again refreshes the period of automatic release of the account.

Checking the account

How to select

Description of service:
Checking if the account has been called on a specific phone.

Changing the account's PIN (#55)

How to select

Description of service:

The service enables changing the account's PIN code. If the PIN code is changed on a virtual account, it should be called on any phone using #53 before. The PIN change service does not work for an account called using #52. This service is available only internally.

Call forwarding

The services associated with forwarding are all functions that enable programming a PBX to automatically re-route the calls to another phone or account.

I am here temporarily (#57)

Calling the service

How to select this service

Description of service
The service #57 can be used in two situations:

1. If you want to forward all calls incoming to the number of the subscriber that originates the service to the phone with this function activated. Forwarding is always performed after two rings at the original phone of the subscriber that activated the service. The service can be performed for multiple subscribers on a single phone.
2. If you want to signal at the equipment that was used to call the service when a new message is left on the group's voice mail (use the catalogue number and PIN of the voice mailbox during activation).

Entering the wrong PIN code three times locks the services. Unlocking is possible using the service #999

Cancelling the service

How to select

Description of service
Deactivating the I am here service. The service is also cancelled automatically (provided it was not used for notification about new messages see paragraph 2 above) in the following cases:

• after picking up the handset on the original phone,
• after the period defined in the PBX,
• when calling the "original" phone from the phone used for calling the service (calling the number that was used after the #57 sequence).

Call forwarding, with the Do not disturb [DND] service active (#73)

First method for the service activation

How to select

Description of service
The service re-routes the incoming calls.
When selecting the type of forwarding you can precisely define which calls should be forwarded after the #73 function is called:

X=0 all,

X=1 only direct outgoing calls,

X=2 only extension direct,

X=3 only outgoing calls with announcement,

X=4 only from the group.

X=0..3 applies to incoming calls for the subscriber

X=4 applies to incoming calls to the group

The service is also available after logging in to a DISA account.

Second method for the service activation

Description of service
The service re-routes the incoming calls. In this case the type of calls being re-routed is not specified. By default, forwarding is set for all calls (X=0 all).

Cancelling the forwarding when DND

How to select
Description of service
Deactivating the call forwarding when DND.

Checking the forwarding status when DND

How to select

Description of service
Checking if the forwarding service is activated when DND. Pressing (#73**) again will change the service status (the service will be deactivated if it was active).

Unconditional forwarding (#74)

First method for calling the service

How to select
Description of service
The service performs unconditional forwarding of incoming calls.

When selecting the type of forwarding you can precisely define which calls should be forwarded after the #74 function is called:

X=0 all,

X=1 only direct outgoing calls,

X=2 only extension direct,

X=3 only outgoing calls with announcement,

X=4 only from the group.

X=0..3 applies to incoming calls for the subscriber

X=4 applies to incoming calls to the group

The service is also available after logging in to a DISA account.

Second method for the service activation:

How to select

Description of service
The service performs unconditional forwarding of incoming calls. In this case the type of calls being re-routed is not specified. By default, forwarding is set for all calls (X=0 all).

Cancelling the unconditional forwarding

How to select

Description of service
Deactivating the unconditional forwarding

Checking the unconditional forwarding

How to select

Description of service
Checking if the unconditional forwarding is activated. Pressing (#74**) again will change the service status (the service will be deactivated if it was active).

Warning:
If a service has not been activated on the phone, e.g. #74, then it is not possible to use #74** to change the service status. PBX remembers only the last activated type of forwarding (example: you activate #74 service so you can't check and change the status using #76**; you can only check and change the service status using #74**).

Call forwarding when busy (#75)

First method for calling the service

How to select
Description of service
The service re-routes the incoming calls.

When selecting the type of forwarding you can precisely define which calls should be forwarded after the #75 function is called:

X=0 all,

X=1 only direct outgoing calls,

X=2 only extension direct,

X=3 only outgoing calls with announcement.

X=0..3 applies to incoming calls for the subscriber

The service is also available after logging in to a DISA account.

Second method for the service activation

How to select

Description of service

The service re-routes the incoming calls. In this case the type of calls being re-routed is not specified. By default, forwarding is set for all calls (X=0 all).

Cancelling call forwarding when busy

How to select

Description of service

Deactivating call forwarding when busy.

Checking call forwarding when busy

How to select

Description of service

Checking if call forwarding when busy is activated. Pressing (#75**) again will change the service status (the service will be deactivated if it was active).

Warning: If a service has not been activated on the phone, e.g. #75, then it is not possible to use #75** to change the service status. PBX remembers only the last activated type of forwarding (example: you activate #74 service so you can't check and change the status using #76**; you can only check and change the service status using #74**).

Call forwarding when unavailable (#76)

First method for calling the service

How to select

Description of service

PBX forwards calls to the defined number when the call is not answered after the specified number of rings is passed.

When selecting the type of forwarding you can precisely define which calls should be forwarded after the #76 function is called:

X=0 all,

X=1 only direct outgoing calls,

X=2 only extension direct,

X=3 only outgoing calls with announcement,

X=4 only from the group.

X=0..3 applies to incoming calls for the subscriber

X=4 applies to incoming calls to the group

The service is also available after logging in to a DISA account.

Second method for the service activation

How to select

Description of service

PBX forwards calls to the defined number when the call is not answered after the specified number of rings is passed. By default, forwarding is set for all calls (X=0 all).

Cancelling call forwarding when unavailable

How to select

Description of service Deactivating call forwarding when unavailable on a specific phone (account).

Checking call forwarding when unavailable

How to select

Description of service

Checking if call forwarding when unavailable is activated. Pressing (#76**) again will change the service status (the service will be deactivated if it was active).

Warning:
If a service has not been activated on the phone, e.g. #74, then it is not possible to use #74** to change the service status. PBX remembers only the last activated type of forwarding (example: you activate #74 service so you can't check and change the status using #76**; you can only check and change the service status using #74**).

Setting the number of rings after which call will be forwarded for the service #76 (#71)

How to select

Description of service
Defining the number of rings (n=0..9) needed for call forwarding installed on the phone (account) to be activated.

The service is also available after logging in to a DISA account.

Deactivating all forwarding services (#70)

Service activation

How to select

Description of service

Using this service you can cancel call forwarding regardless of their type.

The service is also available after logging in to a DISA account.

Checking if all forwarding has been deactivated

How to select

Description of service

Checking if the specific subscriber has any active call forwarding. If there are active forwarding services, they will get the message: Service active, if not: Service inactive.

MobilePhone #77

Full description of the operation of the MobilePhone function can be read here

Configuration

• This function is active only for PBX types MAC-6400 and CXS-0424
• The MobilePhone telephone number associated with the original phone is associated by the Admin in the PBX configuration
• Time period after which the MobilePhone service is activated is set by the Admin in the PBX setup
• The user of a basic phone can activate/deactivate the MobilePhone function by themselves
• The number of persons that can use the MobilePhone function is determined by the type of purchased licence. In a PBX without a licence MobilePhone can be activated for a single user.

How to select

Depending on the parameter value, MobilePhone will be activated in the following way:
1) When the call is not answered on the base phone or the DND function is activated

2) Only if the call will not be answered on the base phone

3) Only when DND is activated on the base phone.
Warning: If the phone with MobilePhone is activated by DND, no standard or private DND message is played

0) Switching off the MobilePhone function

Services associated with phone number presentation

Temporary CLIR (#23)

How to select

Description of service This service results in a temporary restriction of line presentation in outgoing traffic during a single call. Despite number restriction, some authorities (e.g. the police, emergency ambulance service) are still able to view it. This service does not apply to outgoing calls made using analogue outgoing lines.

The service is also available after logging in to a DISA account.

Services associated with outgoing calls

Urgent calls (#25)

How to select

Description of service Enables the subscribers to use a special line, when all normally available lines are in use. For example, all calls to GSM are led via a gateway. When all GSM lines of a gateway are seized, the subscribers with privileges to urgent calls will be able to make calls to a GSM network, e.g. using ISDN lines. In all cases, the details depend on the configuration of an individual PBX. This service is available if the user has the privileges to use it assigned in the PBX. The service is also available after logging in to a DISA account.

Private calls (#27)

How to select

Description of service One of the uses of the private call function can be the creating of individual call tariffs for subscribers. A subscriber must have the privileges to make private calls. The private calls can be made using lines other than the ones used for the other calls and can also be subjected to independent call tariffs in BillingMAN.

The service is also available after logging in to a DISA account.

Emergency working mode of a PBX for the outgoing calls (#80)

How to select
Where if

• 1 - switching on the service
• 0 - switching off the service

This service is used for switching PBX to special working mode in case of a failure of outgoing lines that the PBX cannot resolve automatically. These include poor quality of VoIP connections associated with periodic decrease of quality of Internet connection.
The elements necessary to call the service:

• User has privileges to change the working mode using the service #87
• User knows the PIN that enables changing the working mode using the service #87
• Unlocked phone and locked phone

Remember that after switching on the function it will be active until it is manually switched off.
After this function has been recalled, all subscribers that make outgoing calls obtain special access class for the outgoing calls and due to that the outgoing calls will be made using outgoing lines.
Calling the service has not influence the organization of incoming call and the subscriber's rights.
To assure correct operation of the service the PBX must be programmed correctly by admin.
Checking the operation of the service

After selecting the code for checking the service, the PBX plays the following message:
"Service active"
or
Service inactive.

Services associated with incoming calls

Manual change of working mode (#87)

How to select

Description of service

Setting the period of activity for the specific operating mode until a specific time. When the defined hour is reached, the PBX will be switched to automatic mode assigned to this time. Manual change of operating mode influences the automatic locking and unlocking of phones depending on the operating mode selected manually.

The service is also available after logging in to a DISA account.

Completely manual change of working mode

How to select

Description of service
Setting a specific working mode to operate until the time of the next manual change. Completely manual change of working mode influences the automatic locking and unlocking of phones depending on the working mode selected manually.

Manual change of working mode without setting time

How to select

Description of service

Setting the operation of a specific working mode until the nearest automatic mode change according to the PBX settings. Manual change of working mode without setting the time influences the automatic locking and unlocking of phones depending on the working mode selected manually.

Warning: Resetting the PBX restores the working mode that was active before the reset.

Return to automatic working mode

How to select

Description of service Return to automatic working mode.

Checking if the manual working mode is active

How to select

Description of service

Checking if the manual working mode is active.

Malicious Call Identification service MCID (#88)

How to select

Description of service

The MCID (Malicious Call Identification) service can be used during and after the call. Selecting this service results in recording this call in PBX CCT-1668 and in the operator's superordinate exchange (if the call was set up by ISDN lines). This enables the operator to identify the data of unwanted calls.

Voice Mail

Voice mail activation

How to select

Description of service
When voice mail is activated calls are forwarded to the catalogue number of an individual or group voice mail (the numbers are defined by the PBX admin, the default value for individual voice mail is 1000). It is possible to precisely define the type of this forwarding by selecting one of the sequences:

3 forward to voice mail when the subscriber has DND activated,

4 forward to voice mail unconditionally,

5 forward to voice mail when the subscriber is busy,

6 forward to voice mail when the subscriber is unavailable.

as well as the type of calls to be forwarded if activated using the 1st method (X=0..3 or 0..4 - the range depends on the type of forwarding) or setting a default value (X=0 forwarding of all calls) in the case of method II.

This service can also be called with default parameters by selecting:

When the Voice mail service is activated:

• when the call originator dials the number of subscriber, they receive the following message: This is voice mail. Leave a message after the beep. or Voice mail full. (if the voice mailbox of the subscriber you are trying to reach is full), provided that the subscriber called does not have service #79 activated,
• If the subscriber has service #79 activated, then after the call originator dials their number, the originator will hear the recorded DND message followed by a sound that informs about the start of voice mail recording or by a message Voice mail full.(when the voice mailbox of the subscriber you are calling is full).

Warning: The capacity of a voice mailbox (allowed total time of all messages but no more than 20 messages) regardless of its type (a subscriber's or public voice mail) is defined by the PBX admin. Maximum time of a single recording is 30seconds.

Warning: You should remember that the DND message is shared between the DND (Do not disturb - #22) and voice mail services, i.e. if the subscriber has #79 service activated, then the same message will be played to the originator both when DND and voice mail services are activated.

Playing voice mail messages

How to select

The user must enter a PIN code after dialling a number if the PBX admin enabled the voice mail logging with PIN option.

Description of service

After a new message is recorded on an individual voice mail, the subscriber will be informed about it:

• the phone will ring once,
• voice mail catalogue number will be shown on the display,
• New message will be heard after picking up the handset (or after switching on the 'Hands Free' mode).

If a new message appears on the group voice mail, then on the device used to call the I am here (#57 including the voice mail catalogue number):

• the phone will ring once,
• group voice mail catalogue number will be shown on the display,

To listen to the message, simply call the number of individual (default: 1000) or group voice mail, enter the PIN after a short sound, if required and then follow the voice instructions. Each message has a sound at the beginning and at the end of it to clearly indicate its time. A message can be played at another phone using a temporary (#52) or permanent (#53) account.
Entering the wrong PIN code three times locks the services. Unlocking is possible using the service #999

Other services

Unlocking a locked subscriber's account #999

If during the operation of a service that requires entering a PIN code, the code is entered incorrectly 3 times, then all services that require entering a PIN become locked. The person performing the services is not informed about the lock but any attempt to perform the service results in the message "Service unavailable". The information about the lock is available for the PBX admin and shown in the event history with the phone on which the incorrect PIN was entered 3 times.
The lock can be deactivated in the following method:

The entered PIN must be correct.
WARNING: After three unsuccessful attempts to unlock the telephone using #999 service caused by entering incorrect code, the services that require entering a PIN will be permanently locked and the intervention of the system's admin will be required.

Hotel status (#82)

How to select

Description of service

Records Hotel status in the conversation buffer after dialling a code on the telephone (max. 16digits). The service informs the hotel software that works with the PBX about the status of a hotel room (e.g. cleaned). The code is defined in the hotel software by the admin.

Access to records from Public phone book from analogue and ISDN phones

Calling from the directory using index

How to select

Description of service

Every record in the Public phone book has an index (an assigned successive number). The knowledge of these indexes enables calling the numbers entered into the directory from analogue and ISDN phones. Record indexes can be read at system phones CTS-202 or request the PBX admin to print the Public phone book.

Call override

This service is available only from the system phones series CTS-202
How to select

Description of service
Call override service enables the subscriber (with such privileges assigned by the PBX admin and equipped with any system phone series CTS-202) to override the conversation of two subscribers and to disconnect them if necessary. This is possible if none of the participants do not have the protection against this service enabled (by the PBX admin).

Alarm call service (#28)

Service activation

How to select

Description of service

This service enables setting a alarm call at a specified time to the minute (HH - hour, MM - minutes). The alarm clock rings again for a max. 3 times, every 5 minutes. The service is deactivated after 15 minutes from the time set as the alarm call. Own number and the word "Alarm clock" is sent to the display of the analogue phone. Only the word Alarm clock is displayed on the CTS-202 system phones. After answering a call the subscriber hears the message "The wake up call has been made". For the subscriber that used the service I am here(#57) or Calling the account permanently(#53), the alarm call will be made on the subscriber's original phone. An alarm call will be made even if the subscriber has DND service enabled. If the subscriber is busy (talks on the phone), then the call from the alarm clock will be made after the conversation is finished.

Checking the ringer of your phone

How to select

Description of service

Selecting this function means that the phone will call back immediately after the handset is hanged up.

Cancelling the alarm call

How to select

Description of service

This function cancels the alarm call set previously

Checking the status of alarm call (switch on/off)

How to select

Description of service

This function is intended for checking the status of the alarm call and to deactivate the service at the last defined time. This can be done by selecting additionally .

Auto Redial service

Service activation

How to select

Description of service

If the subscriber you are calling is busy, then after dialling the service code, and when the subscriber becomes available (busy signal before), you will be notified by the ringer and after lifting the handset the system will automatically dial that subscriber's number. This service is available for extension numbers and outgoing calls.

The service will remain valid for:

• 90 minutes in the case of extension calls,
• 10 minutes in the case of outgoing calls (for busy targets).

NOTE: You can stand queue in the case of:

• PBX subscribers using analogue telephones,
• PBX subscribers using CTS-202.CL, CTS-202.Plus or CTS-202.IP system telephones,
• External subscribers available via the ISDN trunk
• External subscribers available via the GSM trunk.

Checking the status of the service

How to select

Description of service
After voice selecting the PBX service code

• Service active

or

• Service inactive

about the current status of the service

Cancelling the service

How to select

Description of service
Dialling the code stops waiting for the subscriber to become available

Auto Redial redialling if unavailable

How to select

Description of service

If the subscriber you are calling is unavailable, then after dialling the service code, and when the subscriber becomes available (was unavailable), you will be notified by the ringer and after lifting the handset the system will automatically dial that subscriber's number. This service is available both for extension and outgoing calls. The operation of the service is limited to:

• 90 minutes in the case of extension calls,
• 60 minutes in the case of outgoing calls.

WARNING:

You can join queue to:

- a PBX subscriber using an analogue phone,

- a PBX subscriber using CTS-202.CL, CTS-202.Plus or CTS-202.IP system phone,

- an external subscriber available via the ISDN trunk,

- an external subscriber available via the GSM trunk.

Checking the status of the service

How to select

Description of service
After voice selecting the PBX service code

• Service active

or

• Service inactive

about the current status of the service

Cancelling the service

How to select

Description of service
Dialling the code stops waiting for the subscriber to become available

Auto Redial redialling if all lines are unavailable

How to select

Description of service If all lines in your PBX are busy when you are trying to make a call, then after dialling the service code, you will be notified by the phone's ringer when a line becomes available. The system will automatically redial the desired number after you pick up the handset.

The service will remain valid for:

• 30 minutes in the case of PBX busy lines.

NOTE: You can stand queue in the case of any busy trunk in PBX. Picking up the handset and dial:

Checking the status of the service

How to select

Description of service
After voice selecting the PBX service code

• Service active

or

• Service inactive

about the current status of the service

Cancelling the service

How to select

Description of service
Dialling the code stops waiting for the subscriber to become available

Callback

The Callback service does not have any code.
The operation of the service is to request a connection with the PBX and after making the connection to enable further calling a number using the PBX.
This function is associated with the service MobilePhone, and the operation of this function partially depends on the configuration of MobilePhone by the system's admin.
A detailed description of the operation of Callback can be read here

Summary of services available at DISA

All the aforementioned services are available for extension numbers and some of the services are available also after logging in to an account to DISA. Below is a summary of these services:

#21 Phone locking

#22 Do not disturb (DND)

#23 Temporary CLIR

#25 Urgent calls

#27 Private calls

#35 Urgent call in a PickUp Group

#52 Temporary account

#7x Transferring calls

#77 - MobilePhone

#79 Private DND message

#87 Change of operating mode

#92 Recording and deleting a word announcement

#999 - Unlocking a locked subscriber's account

Warning: Please note that usually when dialling to DISA, dialling * returns to the redialling. Due to the availability of services also on DISA, the operation of * changes after the service is selected. For example after selecting #76 service the operation of * for redialling will be locked and * will then be used to continue the operation of service.

Safety requirements for operating Slican PBXs

It is essential to comply with the rules governing safety and use to ensure correct operation of this device. Below are the basic elements to be taken into account by the manufacturer in the case of any complaints and claims submitted by users. The rules relate to the installation, location and the requirements for the electrical power supply and data communication network.

Installation:

1. Only authorised or qualified manufacturer's service teams are allowed to install and initialise the device.

1. All the installation procedures should be performed in compliance with the assembly principles as well as any occupational health and safety regulations.

Working Environment:

1. The system telephones must not be installed in rooms featuring high humidity levels. Such rooms may reduce the service life and quality of electronic component functions.

1. To avoid the risk of wetting the device, it should not be located near water containers (such as pools, valves).

1. The PBX must not be located in rooms with high dust concentration or rooms with high-intensity electromagnetic field.

The device may begin to malfunction, be affected by interference, or discolour if installed in places exposed to:

1. Direct sunlight,
2. Frequent or strong vibrations or mechanical impacts,
3. Live antenna radiation (particularly in short wave range).

Electrical requirements:

1. The device must be earthed properly.

1. All devices connected to the PBX must have certificates of conformity with the standards in force in the European Union.

Change history

Release 1.06

1. Increase of number of word announcements in a PBX up to 99.
2. Introducing the service #79 Recording and setting private DND message.
3. New service #28 wake up call.
4. Introducing service #88 MCID - Malicious Call Identification.
5. New service Auto Redial automatic redialling.
6. New functional features: PATHFINDER, Static call routing, INVENIO.
7. Completely manual change of operating mode new service.

Release 1.07

1. Change of the number of subscribers.
2. Changing the functionality of system phones connecting up to 5 consoles to every CTS-202 series phones (max. 4 phones).
3. Added services #34, #51, #58, #59.
4. New functionality - group ACD (call center).

Release 1.08

1. New service voice mail.
2. Extension of the functionality of DND message can be set as a welcome message encouraging to leave a message on voice mail.
3. Extending the functionality of the I am here (#57) service - introducing a sequence to deactivate the service, using the service in the group voice mail.

Release 1.10

1. New service #80 - Switch on/off the emergency operating mode of PBX
2. New service #999 - Unlocking a locked subscriber's account
3. Updated details about the available system phones
4. Added information MobilePhone and Callback