Difference between revisions of "DPH.IP Connecting devices of DPH.IP family"
From pubWiki-en
(Created page with "= Connecting two devices to EZ = Building an ACS based on DPH.IP devices (KS1, KS4, KS16, CR0) should pay attention to connection of individual system components. <br> When yo...") |
(→Connecting two devices to EZ) |
||
| (One intermediate revision by the same user not shown) | |||
| Line 2: | Line 2: | ||
Building an ACS based on DPH.IP devices (KS1, KS4, KS16, CR0) should pay attention to connection of individual system components. <br> | Building an ACS based on DPH.IP devices (KS1, KS4, KS16, CR0) should pay attention to connection of individual system components. <br> | ||
When you connecting DPH.IP doorphone on one side and CR0RF card reader on other side to one EZ, connect appropriate contact inputs (according to diagram below) and program in PBX: <br> | When you connecting DPH.IP doorphone on one side and CR0RF card reader on other side to one EZ, connect appropriate contact inputs (according to diagram below) and program in PBX: <br> | ||
| + | * EZ-SEL jumper in DPH.IP set in NO mode | ||
* connect '' 'EZ' '' output of TBRD.CR to '' 'EZ' '' | * connect '' 'EZ' '' output of TBRD.CR to '' 'EZ' '' | ||
* connect '' 'POD' '' input of TBRD.CR with '' 'EZ' '' output of DPH.IP | * connect '' 'POD' '' input of TBRD.CR with '' 'EZ' '' output of DPH.IP | ||
| Line 15: | Line 16: | ||
* NCP | * NCP | ||
| − | ** for DPH.IP doorphone | + | ** for DPH.IP doorphone in Extensions/Devices/DPH.IP/Doorphones/EZ output settings set option: |
| − | ** for CR0RF reader | + | *** Enabled, Mode: Normally inactive |
| − | *** | + | ** for CR0RF reader in Extensions/Devices/DPH.IP/Doorphones/POD input settings set options: |
| − | *** | + | *** Enabled, Resting state: Normally open |
| + | *** If POD button is pressed: Open EZ lock: V | ||
Latest revision as of 13:26, 30 June 2020
Connecting two devices to EZ
Building an ACS based on DPH.IP devices (KS1, KS4, KS16, CR0) should pay attention to connection of individual system components.
When you connecting DPH.IP doorphone on one side and CR0RF card reader on other side to one EZ, connect appropriate contact inputs (according to diagram below) and program in PBX:
- EZ-SEL jumper in DPH.IP set in NO mode
- connect 'EZ' output of TBRD.CR to 'EZ'
- connect 'POD' input of TBRD.CR with 'EZ' output of DPH.IP
PBX configuration:
- IPx/CCT/MAC
- for DPH.IP doorphone in ConfigMAN Peripherals/Doorphones/DPH.IP/Hardware settings set option:
- OpMD (Output mode 'EZ' ): Switched off
- for CR0RF reader in ConfigMAN Peripherals/Doorphones/DPH.IP/Hardware settings set options:
- POD (POD): Button
- NmPOD (Normal POD state): Normally open
- for DPH.IP doorphone in ConfigMAN Peripherals/Doorphones/DPH.IP/Hardware settings set option:
- NCP
- for DPH.IP doorphone in Extensions/Devices/DPH.IP/Doorphones/EZ output settings set option:
- Enabled, Mode: Normally inactive
- for CR0RF reader in Extensions/Devices/DPH.IP/Doorphones/POD input settings set options:
- Enabled, Resting state: Normally open
- If POD button is pressed: Open EZ lock: V
- for DPH.IP doorphone in Extensions/Devices/DPH.IP/Doorphones/EZ output settings set option:
